GE Lighting WGZ100 Manual De Usuario

WARNING/AVERTISSEMENT

Read these instructions completely and carefully.

Turn power off before inspection, installation or removal.

Properly ground electrical enclosure.

Follow all NEC and local codes.

Use only UL approved wire for input/output connections.

Minimum size 14 AWG for continuous runs.

Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

Coupez l'alimentation avant d'inspecter, installer ou déplacer le luminaire.
Assurez-vous de correctement mettre à la terre le boitier d'alimentation électrique.

Respectez tous les codes NEC et codes locaux.

N'utilisez que des fils approuvés par UL pour les entrées / sorties de 

connexion. Taille minimum 14 AWG.

Lighting Solutions

WGZ100

24-14

   Left : (N)Input、(L)Input、(L)Relay Output

Right : 0-10V GND、0-10V OUT、Dali+、Dali-

or LED  Driver

for P2 terminal

Translate Wireless ZigBee messaging to control electronic ballast or LED Driver:

32mA

Type 1.B action    Pollution degree 2     Rated Impulse voltage 4000V

210*290mm

正面

背面

(N) Input                 White
(L) Input                 Black
(L) Relay Output    Red

(-)  0-10V GND   Grey
(+) 0-10V OUT    Purple

0-10V LED Driver

ZigBee to 0-10V Interface

Driver Line      (L)

Driver Neutral    (N)

Wire Nut

(N) (L)

Driver 0-10V Dimming Wires

Driver LED Output Wires 

(to LED Array)

(+)

(-)

Fixture Mains 

(via code-compliant conduit) 

Fixture Driver Housing 
(or code-compliant wiring box)

(+)

(-)

The interface and wiring is intended to be installed and 
completely enclosed within the same NEC Class 1 driver 
housing as the 0-10V driver using metal mounting screws 
(not provided).

(Relay Output)

(L)

(N)

(Relay Output)

(N) (L)

Caution: The user is cautioned that changes or modifications not expressly approved by the party 
responsible for compliance could 
void the user's authority to operate the equipment. 
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This 
equipment should be 
installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

This device complies with Industry Canada’s license exempt RSSs. Operation is subject to the following two 
conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause undesired operation of 
the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de 
licence. L'exploitation est 
autorisée aux deux conditions suivantes : 
(1) l'appareil ne doit pas produire de brouillage, et 
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est 
susceptible d'en compromettre le fonctionnement.

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled 
environment. This equipment should 
be installed and operated with a minimum distance of 20cm between the radiator and any part of your 
body.
 
Pour se conformer aux exigences de conformité CNR 102 RF exposition, une distance de séparation d'au 
moins 20 cm doit être maintenue 
entre l'antenne de cet appareil ettoutes les personnes.

FCC sDoC statement
 
                                              
Brand name: GE Lighting / model number: WGZ100
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may 
cause undesired operation. 
Suppliers Name: GE Lighting Solutions
Suppliers Address (USA): Nela Park, Cleveland, Ohio, 44112
Suppliers phone number and / or internet contact information: 1-888-MYGELED