BodyMedia Inc. 155 Manual De Usuario
BodyMedia FIT Armband and Display Manual
BodyMedia FIT Armband and Display Manual
12
Display Battery
If the digits on the Display are faded, and you cannot establish a connection to the
Armband, then the battery may require replacing. The Display comes equipped
with a replaceable CR-2032 coin cell battery with an expected life of 6-12 months
under normal use. When the battery needs to be replaced, it is recommended that
you bring the Display to a jeweler or watch vendor. To replace the battery yourself:
If the digits on the Display are faded, and you cannot establish a connection to the
Armband, then the battery may require replacing. The Display comes equipped
with a replaceable CR-2032 coin cell battery with an expected life of 6-12 months
under normal use. When the battery needs to be replaced, it is recommended that
you bring the Display to a jeweler or watch vendor. To replace the battery yourself:
1. Make sure you have a fresh CR-2032 coin cell battery, a #0 size Phillips head
screwdriver, and a soft cloth.
2. Remove the Display unit from the clip.
3. Turn the unit over onto a soft cloth, revealing the underside, and remove the four
small screws attaching the metal back plate to the Display. Only remove the
screws on the metal back plate, do not remove the screws on the edge of the
Display.
4. Remove the old battery.
5. Press any button on the display for 10 seconds.
6. Place the new battery with the (+) side facing up.
7. Ensure that the black o-ring gasket remains properly seated in the groove to
provide a watertight seal.
8. Reattach the back plate, with the text facing up. Ensure that the arrow that says
up (on the inside of the metal back) points towards the top of the device.
9. Once attached, turn the unit over and press any button to wake the Display.
10. Dispose of the old battery in accordance with local, state, federal, or country
specific regulations.
screwdriver, and a soft cloth.
2. Remove the Display unit from the clip.
3. Turn the unit over onto a soft cloth, revealing the underside, and remove the four
small screws attaching the metal back plate to the Display. Only remove the
screws on the metal back plate, do not remove the screws on the edge of the
Display.
4. Remove the old battery.
5. Press any button on the display for 10 seconds.
6. Place the new battery with the (+) side facing up.
7. Ensure that the black o-ring gasket remains properly seated in the groove to
provide a watertight seal.
8. Reattach the back plate, with the text facing up. Ensure that the arrow that says
up (on the inside of the metal back) points towards the top of the device.
9. Once attached, turn the unit over and press any button to wake the Display.
10. Dispose of the old battery in accordance with local, state, federal, or country
specific regulations.
Note: Once the battery is replaced, you will need to reset the Display. Simultane-
ously press all 4 buttons, “MODE” + “VIEW” + “LIGHT” + “RESET TRIP” for 5
seconds or more. The Display will turn on and the back-light will flash.
ously press all 4 buttons, “MODE” + “VIEW” + “LIGHT” + “RESET TRIP” for 5
seconds or more. The Display will turn on and the back-light will flash.
The Display will turn on and the back-light will flash. Follow the instructions for
“Using the Display” on page
“Using the Display” on page
8 to synchronize again with the Armband.
Energy Information (calories)
Energy information on the Display is reported in kcal. You may convert between
kcal and kJ as follows. 1 kcal equals 4.2 kJ. For example:
Energy information on the Display is reported in kcal. You may convert between
kcal and kJ as follows. 1 kcal equals 4.2 kJ. For example:
The Armband is not designed to be used underwater or to come into continuous
contact with water. Do not immerse the Armband in water.
The Display is water resistant up to 30 meters.
contact with water. Do not immerse the Armband in water.
The Display is water resistant up to 30 meters.
To ensure the Armband and Display are working correctly, they should be cleaned
regularly.
regularly.
Clean the Armband and Display daily after sweating or when either one becomes
noticeably moist or dirty. Failure to keep the Armband and Display clean, or
improper cleaning, may irritate the skin and affect the sensor performance. Do not
noticeably moist or dirty. Failure to keep the Armband and Display clean, or
improper cleaning, may irritate the skin and affect the sensor performance. Do not
13
Water Resistance
Care Instructions
kJ
837
2,092
8,368
10,460
kcal
200
500
2,000
2,500