SmartBridges Pte Ltd NEXUS2 Manual De Usuario
FCC ID PWG NEXUS2 3
Installation Manual
1. Introduction
The smartBridges SB3001 is a complete wirelessLAN high speed Network Interface
Card (NIC) used for Point to Point and Point to Multi Point Links with external
antennas.Developed by modifying GlobespanVirata ISL39200M WLAN NIC, it
conforms to the IEEE 802.11a,b,g protocol , works in point to point and point to
multi point mode and operates in the 2412-2483.5,5250-5350 MHz frequency band. The
device shall not be used in any application other than Point to Point and Point to multi
Point modes.
Card (NIC) used for Point to Point and Point to Multi Point Links with external
antennas.Developed by modifying GlobespanVirata ISL39200M WLAN NIC, it
conforms to the IEEE 802.11a,b,g protocol , works in point to point and point to
multi point mode and operates in the 2412-2483.5,5250-5350 MHz frequency band. The
device shall not be used in any application other than Point to Point and Point to multi
Point modes.
1. The module has Radio PCB and Booster PCB glued together inseparably with
epoxy based potting compound . Any attempt to separate the PCB’s will
destroy both the PCB’s irrepairably . Booster is an amplifier which keeps
intact spectral mask and offers higher receiver sensitivity for the radio. This
platform is used to enhance Nexus features.
destroy both the PCB’s irrepairably . Booster is an amplifier which keeps
intact spectral mask and offers higher receiver sensitivity for the radio. This
platform is used to enhance Nexus features.
2. Antennas qualified with the device are 31dBi Parabolic Dish 5.3 GHz , 31.5 dBi
Parabolic Dish 5.25~5.7GHz , 29dBi Parabolic grid , 29 dBi Panel for 5.25 ~
5.35 GHz band and 5.25 ~ 5.75 GHz bands . For 2.412 ~ 2.485 GHz band
following antennas are qualified : 24 dBi Parabolic Grid , 17 dBi Vertically
Polarised Sector antenna , 16.5 dBi Horizontally Polarised sector antenna , 12 dBi
Omni antenna . Other antennas in the same family but with lower gain are
allowed for use with the device.
5.35 GHz band and 5.25 ~ 5.75 GHz bands . For 2.412 ~ 2.485 GHz band
following antennas are qualified : 24 dBi Parabolic Grid , 17 dBi Vertically
Polarised Sector antenna , 16.5 dBi Horizontally Polarised sector antenna , 12 dBi
Omni antenna . Other antennas in the same family but with lower gain are
allowed for use with the device.
• Fully compliant with the IEEE 802.11a ,b, g WLAN standards for Point to point and
Point to Multi Point links
• FCC Certified Under Part 15 (pending) to Operate in the 5250~5350 , 2412 ~ 2483.5
MHz Bands
• Support for 54, 48, 36, 24, 18, 12, 9, and 6 Mbps OFDM
• Driver Supports Microsoft Windows ® 98/SE, ME, XP and 2000 (SR1)
Point to Multi Point links
• FCC Certified Under Part 15 (pending) to Operate in the 5250~5350 , 2412 ~ 2483.5
MHz Bands
• Support for 54, 48, 36, 24, 18, 12, 9, and 6 Mbps OFDM
• Driver Supports Microsoft Windows ® 98/SE, ME, XP and 2000 (SR1)
2. Installation Procedure
SB 3001 has to be installed inside smartBridges NEXUS 3010 out door specified
back haul device or NEXUS 3020 Access Points or NEXUS 3040 Client Devices .
back haul device or NEXUS 3020 Access Points or NEXUS 3040 Client Devices .
2.1 NEXUS 3010, BackHaul , 3020 , Access Point , 3040 , Client device for
outdoor application
NEXUS 3010 is a Back Haul Point to Point link for carrying high data traffic
. It uses Intel IXP 425 BCT a powerful processor to run the application and
provide high security . It provides two Ethernet ports for connection to network
devices or PC . Antenna is connected to the NEXUS unit .
NEXUS 3020 is a wireless Access Point for high data traffic . It uses the same
hardware as NEXUS 3010 and provides point to multi Point Access .
NEXUS 3040 is a wireless Client device for high speed internet access . It
works with NEXUS 3020 as Access Point . Many clients can be connected to an
Access Point .
NEXUS 3010 , 3020 , 3040 are meant for out door applications . The device has
to be mounted on Tower or roof top along with the antenna . It has all
mounting hardware for this purpose .
2.2 Installing SB 3001 into NEXUS 3010/ 3020/ 3040
The module SB 3001 is normally installed into NEXUS 3010/ 3020/ 3040 in
the factory at the time of manufacturing . NEXUS 3010/ 3210/ 3410 has mini
PCI connector ( socket ). The Radio module SB 3001 can directly fit into the
NEXUS unit and is fixed by screws to the mounting pillars shown .