Panasonic PQWBTG1000N Manual De Usuario

Descargar
Página de 4
3-E Helpful Information
CAUTION:
To reduce the risk of fire or injury to persons, read and follow these instructions.
1. Use only the battery(ies) specified.
2. Do not dispose of the battery(ies) in a fire. They may explode. Check with local
waste management codes for special disposal instructions.
3. Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may
cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.
4. Exercise care in handling batteries in order not to short the battery to conductive
materials such as rings, bracelets, and keys. The battery and/or conductor may
overheat and cause burns.
5. Charge the battery(ies) provided with or identified for use with this product only in
accordance with the instructions and limitations specified in this manual.
WARNING:
TO PREVENT FIRE OF SHOCK HAZARD, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR ANY TYPE OF MOISTURE.
FCC and Other Information
When programming emergency numbers and/or making test calls to emergency
numbers:
1. Remain on the line and briefly explain to the dispatcher the reason for the call
before hanging up.
2. Perform such activities in the off-peak hours, such as early morning hours or late
evenings.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Privacy of communications may not be ensured when using this phone.
CAUTION:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this device.
Note:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures: 
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Some cordless telephones operate at frequencies that may cause interference to
nearby TVs and VCRs. To minimize or prevent such interference, the base of the
cordless telephone should not be placed near or on top of a TV or VCR. If interference
is experienced, move the cordless telephone further away from the TV or VCR. This
will often reduce, or eliminate, interference.
Operating near 2.4GHz electrical appliances may cause interference. Move away from
the electrical appliances.
CAUTION:
To comply with FCC RF exposure requirements, the handset should be carried with
the specific belt-clip provided for the handset to ensure compliance. Other non-tested
belt-clips or similar body-worn accessories may not comply, therefore, should be
avoided.
1
After charging the handset,
the display will show the
following.
2
Enter the 15-digit Base
Unit ID code located on
the bottom of the base
unit.
•If you misdial, press
Digits are erased from the right.
3
Press
.
•A beep sounds and “PLEASE
WAIT!!
” is displayed.
)
(
OK
)
(
2
4
Wait until a beep sounds on the
handset and base unit.
•After a few seconds, the handset
number (1 to 4) will be displayed.
•If “BASE BUSY TRY LATER” is
displayed in step 4, the unit is in use.
Wait until the unit is in the standby
mode, and repeat steps from 2.
•If “ENTER BASE ID” is displayed in
step 3, you entered a wrong Base ID
code. Enter the correct code.
Registration is necessary for cordless handsets. An handset will be assigned the
number at registration. The number is used as the handset number. You can register
up to 4 handsets at the KX-TG1000N base unit. 
Make sure the unit is in the standby mode initially. 
ENTER BASE ID
###############
O K
R
I
I
HANDSET 2
R D L
M E M
M E N U
PLEASE
WAIT!!
SEARCHING
FOR BASE
N E W
M E N U
R
•Recharge the battery when:
—“LOW BATTERY” is displayed, or
—“
” flashes on the display.
Battery information
After your Panasonic battery is fully charged:
∗In case the Range Extender Mode is set to “OFF”, see page 48 in the English
operating instructions.
•Battery life may be shortened depending on usage conditions and ambient temperature.
Clean the charge contacts of the handset and the charger with a soft, dry cloth
once a month. Clean more often if the unit is subject to grease, dust or high
humidity. 
Otherwise the battery may not charge properly.
•The battery cannot be overcharged.
Charging the battery
Place the handset on the charger and charge for about 12 hours
before initial use.
During charging the battery, the battery
icon cycles as shown below.
Up to 5.5 days
Operation
Approx. battery life
While in use (TALK)
Up to 10 hours*
While not in use (Standby)
1-D Battery
Getting Started
Things You Should Know 
Registration
Section 1
Section 2
Section 3
rge 
tacts
FOUND
BASE
R D L
M E M
M E N U