ZTE Corporation B01 Manual De Usuario
Overview
MFB
Front
Back
LED
Speaker
Ear cushion
Microphone
Light BTH
ZTE Bluetooth headset
User Guide
How to use
Power on / off:
Press and hold the MFB for longer than
5 seconds to switch.
Press and hold the MFB for longer than
5 seconds to switch.
Pairing:
Before you can use your headset,you
must pair it with your phone.
Before you can use your headset,you
must pair it with your phone.
Step 1.Press and hold the MFB for
longer than 5 seconds to power on the
headset and put Headset in paring mode.
longer than 5 seconds to power on the
headset and put Headset in paring mode.
Step 2.Turn on the Bluetooth function on
the mobile phone and set the phone to
search for Bluetooth devices.
the mobile phone and set the phone to
search for Bluetooth devices.
Step 3.Select the headset (Light BTH).
* decide by customer of device name.
Step 4.Enter the passcode 0000 to pair
and connect the headset to your phone.
and connect the headset to your phone.
Answering / Ending a call:
Short press the MFB
Short press the MFB
Rejecting an incoming call:
Press and hold MFB for longer than 2
seconds.
Press and hold MFB for longer than 2
seconds.
Redialing last number:
Press and hold MFB for longer than 3
seconds.
Press and hold MFB for longer than 3
seconds.
Talk time
8 Hours
Standby time 120 Hours
Typical -1~4 dBm for Class 2
Out power: -0.5~4 dBm
Typical -1~4 dBm for Class 2
Out power: -0.5~4 dBm
If BT Headset dosen’t connector A.G.,
it will auto-shut down after 300 sec.
it will auto-shut down after 300 sec.
Button Function
Without permission,any company,firm or user shall not alter the frequency,increase the power,
or change the characteristics and functions of the original design of the certified lower power
frequency electric machinery.
or change the characteristics and functions of the original design of the certified lower power
frequency electric machinery.
The application of low power frequency electric machineries shall not affect the navigation safety
nor inter a legal communication, if an Interference is found, the service will be suspended until
improvement is made and the interference no loger exists.
nor inter a legal communication, if an Interference is found, the service will be suspended until
improvement is made and the interference no loger exists.
Button
Headset
Status
Status
Action Function
MFB
Ringing Short
Press
Answer an incoming call
Talking
Talking
Talking
Short Press
Voice Recognition
Power off
Press and hold for longer
than 5 seconds
than 5 seconds
Power on headset and put
Headset into pairing mode
Headset into pairing mode
Power on
Press and hold for longer
than 5 seconds
than 5 seconds
Power off the Headset
Voice dial
Short Press
The phone will enter voice
dial mode (handset must
have this function)
dial mode (handset must
have this function)
Charging
First time use: Charge the headset for
approximately 2 hours,or until the LED
light is off.
approximately 2 hours,or until the LED
light is off.
Step 1.Connect the miniconnector of
chargingcable to
the charging
connector
on the headset.
chargingcable to
the charging
connector
on the headset.
Step 2.Connect the
USBconnector of
charging cable to
the powered USB
port on the
desktop orlaptop.
USBconnector of
charging cable to
the powered USB
port on the
desktop orlaptop.
Step 3.LED will fash
twice when connected
and lights on during charging. After
charging complete, LED will turn off.
Note: Headset is not functional
while charging.
twice when connected
and lights on during charging. After
charging complete, LED will turn off.
Note: Headset is not functional
while charging.
LED Flashing
Event
Flashing Pattern
COMMENT
Power on
Flash 3 times
ON (250ms)
OFF (250ms
ON (250ms)
OFF (250ms
Only applied when user power
on thesystem.
on thesystem.
Power off
Flash 3 times
ON (250ms)
OFF (250ms)
ON (250ms)
OFF (250ms)
Only applied when user
shutdown the
system.
shutdown the
system.
Pairing
ON(300ms)
OFF(300ms)
OFF(300ms)
Standby – No
Connected
Connected
ON(100ms)
OFF(4900ms)
OFF(4900ms)
N/A
Standby -
ACL
connected
ACL
connected
ON(100ms)
OFF(2900ms)
OFF(2900ms)
N/A
SCO
Connected
Connected
ON(100ms)
OFF(1900ms)
OFF(1900ms)
N/A
Charging
ON
N/A
Charging
Complete
Complete
OFF
N/A
N/A
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
. Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority
to operate this equipment.
. This device and its antenna(s) must not be co-located or operating in conjunction
with any other antenna or transmitter.
compliance could void the user's authority
to operate this equipment.
. This device and its antenna(s) must not be co-located or operating in conjunction
with any other antenna or transmitter.
FCC Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.