Newcont Electronic Co. Ltd. NTP-6309 Manual De Usuario
Problem Solving section
For your assistance, we have listed below a few common problems.
Phone does not work, check the following:
1. BASE UNIT is plugged into power source.
2. HANDSET is charged.
3. TONE/PULSE Select switch is in the right position.
4.TELEPHONE LINE CORD is plugged in the TELEPHONE JACK.
Phone does not work, check the following:
1. BASE UNIT is plugged into power source.
2. HANDSET is charged.
3. TONE/PULSE Select switch is in the right position.
4.TELEPHONE LINE CORD is plugged in the TELEPHONE JACK.
Range of phone limited, check the following:
1. ANTENNA on BASE UNIT is raised.
2. BASE UNIT is centrally located in your residence.
3. BASE UNIT is not located near appliances.
1. ANTENNA on BASE UNIT is raised.
2. BASE UNIT is centrally located in your residence.
3. BASE UNIT is not located near appliances.
No dial tone, check the following:
1. TELEPHONE LINE CORD plugs are connected to the TELEPHONE JACK and
TELEPHONE LINE CONNECTION JACK.
2. BASE UNIT is plugged into a power source.
3. IF you had a power failure or had unplugged the BASE UNIT, replace the HANDSET
on the BASE UNIT for 2 to 5 seconds to reset the system.
1. TELEPHONE LINE CORD plugs are connected to the TELEPHONE JACK and
TELEPHONE LINE CONNECTION JACK.
2. BASE UNIT is plugged into a power source.
3. IF you had a power failure or had unplugged the BASE UNIT, replace the HANDSET
on the BASE UNIT for 2 to 5 seconds to reset the system.
Received signal flutters or fades, check the following:
1. BATTERY PACK in HANDSET is fully charged.
2. HANDSET is not far from the BASE UNIT.
3. ANTENNA on BASE UNIT is raised.
Interference on reception, check the following:
1. Noise may be picked up from electrical products in the home or electrical storms.
Generally, this noise is a minor annoyance and should not be interpreted as a defect
in your system. (See Technical Information on page 31.)
2. Choose an alternate channel using the button on the HANDSET.
1. BATTERY PACK in HANDSET is fully charged.
2. HANDSET is not far from the BASE UNIT.
3. ANTENNA on BASE UNIT is raised.
Interference on reception, check the following:
1. Noise may be picked up from electrical products in the home or electrical storms.
Generally, this noise is a minor annoyance and should not be interpreted as a defect
in your system. (See Technical Information on page 31.)
2. Choose an alternate channel using the button on the HANDSET.
Long Distance "LDC" Indicator is not ON when receiving long distance call, check
the following:
1. Your local telephone company can provide the Area Code on an incoming long distance
call.
the following:
1. Your local telephone company can provide the Area Code on an incoming long distance
call.
Excess static, check the following:
1. Check to see that the ANTENNA is not touching another metal object.
2. Raise or reposition the BASE UNIT ANTENNA.
1. Check to see that the ANTENNA is not touching another metal object.
2. Raise or reposition the BASE UNIT ANTENNA.
If after pressing the button, you receive three "beeps" and no dial tone,
check the following:
1. BASE UNIT is plugged into power source.
2. If you had a power failure or had unplugged the BASE UNIT, replace the HANDSET
on the BASE UNIT for 2 to 5 seconds to reset the system.
check the following:
1. BASE UNIT is plugged into power source.
2. If you had a power failure or had unplugged the BASE UNIT, replace the HANDSET
on the BASE UNIT for 2 to 5 seconds to reset the system.
NOTE:
If none of the telephones in the house are working, disconnect one set at a time to verify
that none of the phones are causing the problem. If you still have a problem after doing
this, and your telephone still does not work, please contact your local phone company.
If none of the telephones in the house are working, disconnect one set at a time to verify
that none of the phones are causing the problem. If you still have a problem after doing
this, and your telephone still does not work, please contact your local phone company.
Problem Solving
28
/SCAN
DEL
1.HANDSET ANTENNA
2. NEW CALL/MSG(MESSAGE )WAITING LED Indicator: Blinks when recording a new
incoming call or when receiving a Message Waiting signal, if you have subscribed to a
Voice Mail message service from your local telephone company. (See page 11 ).
3. Large LCD Screen: Shows call information, phone status, prompts and directory items.
HANDSET Controls
4. TALK Button: Press to answer an incoming call or to place a call. Press to end
a call.
5. TEMPORARY TONE Button: Press to temporarily change the dialing mode
from PULSE to TONE for rotary service users . (Press once before entering numbers to
access the Answering System or electronic banking services, etc.)
6. button: Press to access names and numbers stored in the DIRECTORY.
7. FUNC(FUNCTION)/VOICE MAIL /VOICE MAIL Button: (FUNCTION)- Press
and hold down to access Special functions operation in STANDBY mode. (For special
functions see page 19). (VOICE MAIL) - Press to automatically dial the Voice Mail Post
Code in your area to access your Voice Mail message in HANG-OFF mode. (Format) -
Press to change the format of the displayed number when reviewing the Caller ID list or
phone book.
8. /FLASH button: (FLASH) Press to answer a call if you have Call Waiting.
(EDIT) Press to edit listed items.
9. BATT LOW INDICATOR :Appears on the LCD Screen when the battery charge is low.
(See page 26 for detail)
10. Button: Press to move around the Large LCD Screen.
11. HANDSET Volume Control(hi,mid ,low) Switch: Select the receiver volume level
(HI, MID, LOW).
12. HEADSET JACK: For connection your headset plug to enjoy hands-free
communication.(See page 10 for detail.)
13. TELEPHONE KEYPAD: Allows you to make a call depending on pressed button.
(for TELEPHONE KEYPAD characters, see page 24.)
14.
RE/PA Button: (SAVE )Press and hold down to save the changes on the listed
items. (REDIAL) Press to redial the last number you dialed. (PAUSE) Press to insert a
pause while dialing. (You will need the
RE/PA button to dial numbers which use
an alternative Long Distance Access Code.)
15. /SCAN
button: (SCAN) Press to change the operating channel when you hear
interference. (DELETE) press and hold down to delete items or individual characters.
16. CHARGE CONTACTS: For charging the BATTERY PACK inside the HANDSET. We
recommend cleaning the CHARGE CONTACTS periodically with a damp cloth.
D
DIR
DIR
SAVE
SAVE
SAVE
SAVE
DEL