Digi International Inc XBEEPRO2 Manual De Usuario
XBee®/XBee‐PRO® ZB RF Modules
© 2011 Digi International, Inc.
147
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures: Re-orient or relocate the receiving antenna, Increase the separation
between the equipment and receiver, Connect equipment and receiver to outlets on different circuits, or
Consult the dealer or an experienced radio/TV technician for help.
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures: Re-orient or relocate the receiving antenna, Increase the separation
between the equipment and receiver, Connect equipment and receiver to outlets on different circuits, or
Consult the dealer or an experienced radio/TV technician for help.
FCC-Approved Antennas (2.4 GHz)
The XBee and XBee-PRO RF Module can be installed utilizing antennas and cables constructed with
standard connectors (Type-N, SMA, TNC, etc.) if the installation is performed professionally and according
to FCC guidelines. For installations not performed by a professional, non-standard connectors (RPSMA,
RPTNC, etc.) must be used.
standard connectors (Type-N, SMA, TNC, etc.) if the installation is performed professionally and according
to FCC guidelines. For installations not performed by a professional, non-standard connectors (RPSMA,
RPTNC, etc.) must be used.
The modules are FCC approved for fixed base station and mobile applications for the channels indicated in
the tables below. If the antenna is mounted at least 20cm (8 in.) from nearby persons, the application is
considered a mobile application. Antennas not listed in the table must be tested to comply with FCC Section
15.203 (Unique Antenna Connectors) and Section 15.247 (Emissions).
the tables below. If the antenna is mounted at least 20cm (8 in.) from nearby persons, the application is
considered a mobile application. Antennas not listed in the table must be tested to comply with FCC Section
15.203 (Unique Antenna Connectors) and Section 15.247 (Emissions).
XBee RF Modules: XBee RF Modules have been tested and approved for use with all the antennas listed in
the tables below. (Cable-loss IS required when using gain antennas as shown below.)
the tables below. (Cable-loss IS required when using gain antennas as shown below.)
The antennas in the tables below have been approved for use with this module. Digi does not carry all of
these antenna variants. Contact Digi Sales for available antennas.
these antenna variants. Contact Digi Sales for available antennas.
Antennas approved for use with the XBee®/XBee‐PRO® ZB RF Modules (Cable‐loss is not required.)
OMNI-DIRECTIONAL ANTENNAS for All Available Channels
Part Number
Type (Description)
Gain
Application*
Min
Separation
Minimum Cable
Loss/Power
Reduction/
Attenuation
Required
A24-HASM-450
Dipole (Half-wave articulated RPSMA - 4.5”)
2.1 dBi
Fixed/Mobile
20 cm
N/A
A24-HABSM
Dipole (Articulated RPSMA)
2.1 dBi
Fixed
20 cm
N/A
A24-HABUF-P5I
Dipole (Half-wave articulated bulkhead mount U.FL. w/ 5”
pigtail)
2.1 dBi
Fixed
20 cm
N/A
A24-HASM-525
Dipole (Half-wave articulated RPSMA - 5.25")
2.1 dBi
Fixed/Mobile
20 cm
N/A
A24-QI
Monopole (Integrated whip)
1.5 dBi
Fixed
20 cm
N/A
29000294
Integral PCB antenna (S2B only)
-0.5 dBi
Fixed/Mobile
20 cm
N/A
29000095
Dipole (Half-wave articulated RPSMA - 4.5”)
2.1 dBi
Fixed/Mobile
20 cm
N/A
29000430
Integral PCB Antenna (XBee-PRO S2 only)
-0.5 dBi
Fixed/Mobile
20 cm
N/A