Option NV OMO6012 Manual De Usuario
GTM601W
FCC-ID:
NCMOMO6012
IC: 2734A-MO6012
Certification Leaflet
AGENCY REQUIREMENTS
Licensed by QUALCOMM Incorporated under one or more of the following United States Patents and/or their counterparts
in other nations: 4,901,307; 5,490,165; 5,056,109; 5,504,773; 5,101,501; 5,506,865; 5,109,390; 5,511,073; 5,228,054;
5,535,239; 5,267,261; 5,544,196; 5,267,262; 5,568,483; 5,337,338; 5,600,754; 5,414,796; 5,657,420; 5,416,797;
5,659,569; 5,710,784; 5,778,338
Federal communications commission notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
> Reorient or relocate the receiving antenna.
> Increase the separation between the equipment and receiver.
> Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
> Consult the dealer or an experienced radio or television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly
approved by Option could void the user's authority to operate the equipment.
Licensed by QUALCOMM Incorporated under one or more of the following United States Patents and/or their counterparts
in other nations: 4,901,307; 5,490,165; 5,056,109; 5,504,773; 5,101,501; 5,506,865; 5,109,390; 5,511,073; 5,228,054;
5,535,239; 5,267,261; 5,544,196; 5,267,262; 5,568,483; 5,337,338; 5,600,754; 5,414,796; 5,657,420; 5,416,797;
5,659,569; 5,710,784; 5,778,338
Federal communications commission notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
> Reorient or relocate the receiving antenna.
> Increase the separation between the equipment and receiver.
> Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
> Consult the dealer or an experienced radio or television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly
approved by Option could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC rules.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Exposure Information to Radio Frequency Energy
Users concerned with the risk of Radio Frequency exposure may wish to limit the duration of their calls and to position the
antenna as far away from the body as is practical.
Modular approval
The module can be integrated into fixed or mobile categorized end-products, so that 20 cm separation distance to end-
user can be assured. You can integrate the module in a portable device, in this case a permissive change application
would be required.
Approbation par module
Le module peut être incorporé à un produit final classé comme fixe ou mobile, mais d’une manière à garantir que l’usager
final soit à une distance de 20 cm. Vous pouvez incorporer le module à un appareil portable, et dans ce cas, une
demande de changement autorisée serait requise.
Device marking
The integrated device must carry the CE mark and Notified body number of the Notified Body used in the Annex IV
conformity assessment of the module on the manufacturing label as described in the R&TTE directive 1999/5/EC Annex
VII. This Notified Body approval only applies to the module and not the final integrated product. The final integrated
product should undergo its own conformity process to the R&TTE directive and should meet all applicable CE marking
directives in order to place the CE mark on the final integrated product.
The end device must also be appropriatly marked with the FCC identification as described in FCC Part 2.925 and 2.926.
Industry Canada requires the host device to be marked with “Contains transmitter module IC: 2734A-MO6012” conform to
section 3.2.1 from the RSS-GEN guidelines.
Marquage du dispositif
Le dispositif incorporé doit porter la marque CE et le numéro de l’organisme notifié utilisé dans l’Annexe IV de l’évaluation
de la conformité du module, sur l’étiquette de fabrication, tel que décrit dans l’Annexe VII portant sur les équipements
radio et équipements terminaux de télécommunication (« R&TTE »). Cette approbation de l’organisme notifié ne
s’applique qu’au module et non au produit final après intégration. Le produit final après intégration devrait être lui-même
l’objet d’un processus d’évaluation de la conformité à la directive sur les équipements radio et équipements terminaux de
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Exposure Information to Radio Frequency Energy
Users concerned with the risk of Radio Frequency exposure may wish to limit the duration of their calls and to position the
antenna as far away from the body as is practical.
Modular approval
The module can be integrated into fixed or mobile categorized end-products, so that 20 cm separation distance to end-
user can be assured. You can integrate the module in a portable device, in this case a permissive change application
would be required.
Approbation par module
Le module peut être incorporé à un produit final classé comme fixe ou mobile, mais d’une manière à garantir que l’usager
final soit à une distance de 20 cm. Vous pouvez incorporer le module à un appareil portable, et dans ce cas, une
demande de changement autorisée serait requise.
Device marking
The integrated device must carry the CE mark and Notified body number of the Notified Body used in the Annex IV
conformity assessment of the module on the manufacturing label as described in the R&TTE directive 1999/5/EC Annex
VII. This Notified Body approval only applies to the module and not the final integrated product. The final integrated
product should undergo its own conformity process to the R&TTE directive and should meet all applicable CE marking
directives in order to place the CE mark on the final integrated product.
The end device must also be appropriatly marked with the FCC identification as described in FCC Part 2.925 and 2.926.
Industry Canada requires the host device to be marked with “Contains transmitter module IC: 2734A-MO6012” conform to
section 3.2.1 from the RSS-GEN guidelines.
Marquage du dispositif
Le dispositif incorporé doit porter la marque CE et le numéro de l’organisme notifié utilisé dans l’Annexe IV de l’évaluation
de la conformité du module, sur l’étiquette de fabrication, tel que décrit dans l’Annexe VII portant sur les équipements
radio et équipements terminaux de télécommunication (« R&TTE »). Cette approbation de l’organisme notifié ne
s’applique qu’au module et non au produit final après intégration. Le produit final après intégration devrait être lui-même
l’objet d’un processus d’évaluation de la conformité à la directive sur les équipements radio et équipements terminaux de