JTECH Communications Inc. SERIES2600 Manual De Usuario
JTECH UHF Desktop Transmitter Installation and Operation Guide 320115K
Page 10
Receiving and Reading Messages
When a page is received, the pager alerts for 4-seconds. Press and release the
button to stop the alert. Press and release the button again to display the
message. Messages containing more than 12 digits continue on a second
screen, which is indicated by a continuation arrow (Æ) in the lower right corner of
the display. The second screen displays automatically after 4-seconds or by
pressing the button if there is rollover data. The number of unread messages is
indicated on the display (e.g. 01 PAGE). Up to ten 16-digit messages can be
stored in the pager. To read other messages, continue pressing the button to
scroll through the messages.
"FULL" is displayed when there are too many unread messages in memory. If
this happens, an incoming message bumps the first (oldest) message, whether
read or unread, out of memory. After scrolling through all of the messages, the
standby screen is displayed. The duplicate message indicator is displayed in the
upper-right corner if the same message is received more than once.
Deleting Messages
To delete an individual message: Display the message to be deleted by
depressing the button for 2-seconds. Depress and hold button until the LCD
displays "DEL" and then release button. To delete all messages: From the
JTECH standby screen depress and hold the button until the LCD shows
"ERASE ALL" and release the button. This will delete all messages except
Unread Messages. The display will return to the standby screen (JTECH).
To delete an individual message: Display the message to be deleted by
depressing the button for 2-seconds. Depress and hold button until the LCD
displays "DEL" and then release button. To delete all messages: From the
JTECH standby screen depress and hold the button until the LCD shows
"ERASE ALL" and release the button. This will delete all messages except
Unread Messages. The display will return to the standby screen (JTECH).
Battery Installation
Battery installation is identical to the process described in the RapidCall vibration
pager section. Similarly, installing the battery will turn the pager on. The pager
will enter a self-test mode by emitting one short beep and vibration; the red and
green LED lamps will turn on for 1-second each. The LCD will then initially
display 88888888, all ICONS and then the pager will display "JTECH" on the
display. Be advised that changing the battery resets the pager memory, erasing
stored messages. Please remember to read all messages before removing the
battery.
Battery installation is identical to the process described in the RapidCall vibration
pager section. Similarly, installing the battery will turn the pager on. The pager
will enter a self-test mode by emitting one short beep and vibration; the red and
green LED lamps will turn on for 1-second each. The LCD will then initially
display 88888888, all ICONS and then the pager will display "JTECH" on the
display. Be advised that changing the battery resets the pager memory, erasing
stored messages. Please remember to read all messages before removing the
battery.
Note: Typical operation of the button is to initiate power on, change the mode of
alerting, read messages, delete messages or turn the pager off. Depressing then
releasing the button in less than 2 seconds will bring up messages. Advancing
through messages is done in the same manner. Depressing the button for over 2
seconds brings up the delete message function or the scroll list depending on
what state the pager is in when the button is depressed. If the button is
depressed for over 2 seconds while a message is displayed, the delete function
is activated. This is a non-reversible function and that message will be deleted.
If the button is depressed and held for over 2 seconds while the pager was in
standby mode ("JTECH" displayed on the LCD) then the scroll list will appear.
alerting, read messages, delete messages or turn the pager off. Depressing then
releasing the button in less than 2 seconds will bring up messages. Advancing
through messages is done in the same manner. Depressing the button for over 2
seconds brings up the delete message function or the scroll list depending on
what state the pager is in when the button is depressed. If the button is
depressed for over 2 seconds while a message is displayed, the delete function
is activated. This is a non-reversible function and that message will be deleted.
If the button is depressed and held for over 2 seconds while the pager was in
standby mode ("JTECH" displayed on the LCD) then the scroll list will appear.