ZyXEL Communications Corporation EMG2881-T20A Manual De Usuario
Chapter 9 Applications
EMG2881-T20A User’s Guide
84
DiffServ
QoS is used to prioritize source-to-destination traffic flows. All packets in the flow are given the same
priority. You can use CoS (class of service) to give different priorities to different packet types.
priority. You can use CoS (class of service) to give different priorities to different packet types.
DiffServ (Differentiated Services) is a class of service (CoS) model that marks packets so that they
receive specific per-hop treatment at DiffServ-compliant network devices along the route based on the
application types and traffic flow. Packets are marked with DiffServ Code Points (DSCPs) indicating the
level of service desired. This allows the intermediary DiffServ-compliant network devices to handle the
packets differently depending on the code points without the need to negotiate paths or remember
state information for every flow. In addition, applications do not have to request a particular service or
give advanced notice of where the traffic is going.
receive specific per-hop treatment at DiffServ-compliant network devices along the route based on the
application types and traffic flow. Packets are marked with DiffServ Code Points (DSCPs) indicating the
level of service desired. This allows the intermediary DiffServ-compliant network devices to handle the
packets differently depending on the code points without the need to negotiate paths or remember
state information for every flow. In addition, applications do not have to request a particular service or
give advanced notice of where the traffic is going.
DSCP and Per-Hop Behavior
DiffServ defines a new Differentiated Services (DS) field to replace the Type of Service (TOS) field in the IP
header. The DS field contains a 2-bit unused field and a 6-bit DSCP field which can define up to 64
service levels. The following figure illustrates the DS field.
header. The DS field contains a 2-bit unused field and a 6-bit DSCP field which can define up to 64
service levels. The following figure illustrates the DS field.
DSCP is backward compatible with the three precedence bits in the ToS octet so that non-DiffServ
compliant, ToS-enabled network device will not conflict with the DSCP mapping.
compliant, ToS-enabled network device will not conflict with the DSCP mapping.
The DSCP value determines the forwarding behavior, the PHB (Per-Hop Behavior), that each packet
gets across the DiffServ network. Based on the marking rule, different kinds of traffic can be marked for
different kinds of forwarding. Resources can then be allocated according to the DSCP values and the
configured policies.
gets across the DiffServ network. Based on the marking rule, different kinds of traffic can be marked for
different kinds of forwarding. Resources can then be allocated according to the DSCP values and the
configured policies.
IP Precedence
Similar to IEEE 802.1p prioritization at layer-2, you can use IP precedence to prioritize packets in a layer-3
network. IP precedence uses three bits of the eight-bit ToS (Type of Service) field in the IP header. There
are eight classes of services (ranging from zero to seven) in IP precedence. Zero is the lowest priority
level and seven is the highest.
network. IP precedence uses three bits of the eight-bit ToS (Type of Service) field in the IP header. There
are eight classes of services (ranging from zero to seven) in IP precedence. Zero is the lowest priority
level and seven is the highest.
Automatic Priority Queue Assignment
If you enable QoS on the EMG2881-T20A, the EMG2881-T20A can automatically base on the IEEE 802.1p
priority level, IP precedence and/or packet length to assign priority to traffic which does not match a
class.
priority level, IP precedence and/or packet length to assign priority to traffic which does not match a
class.
Level 1
This is typically used for non-critical “background” traffic such as bulk transfers that are allowed but
that should not affect other applications and users.
that should not affect other applications and users.
Level 0
Typically used for best-effort traffic.
DSCP (6 bits)
Unused (2 bits)
Table 38 IEEE 802.1p Priority Level and Traffic Type
PRIORITY
LEVEL
TRAFFIC TYPE