Applied Concepts Inc ACMI007 Manual De Usuario
Applied Concepts 011-0131-00 rev 2
Page 30
Setting ID
S
ta
ti
o
n
a
ry
2
3
2
&
4
8
5
S
p
e
e
d
o
m
e
te
r
2
3
2
&
4
8
5
T
ra
ff
ic
2
3
2
Available Values
Dec
Hex
Setting Description
Appendix C Ref
Default Setting
85
0x55
Target Strength Sensitivity
3 – Target Recognition
32
--
--
1 (min) – 32 (max)
87
0x57
Sensitivity Hysteresis
3 – Target Recognition
0
--
--
0 – 3
88
0x58
Holdover Delay
5 – Speed Presentation
45
45
45
Stationary and Traffic: 1 – 222 (~10
sec)
Speedometer: fixed at 45 (~2 sec)
sec)
Speedometer: fixed at 45 (~2 sec)
90
0x5A Format D Polled Modes
2 – Serial Port Configuration
0
232
only
--
--
0 = Polled Mode Disabled
1 = Polled Mode Enabled
Active for Serial Formats D0-D4 only
1 = Polled Mode Enabled
Active for Serial Formats D0-D4 only
91
0x5B
Format D Direction
Character Enable
Character Enable
2 – Serial Port Configuration
0
--
--
0 = Direction Character Disabled
1 = Direction Character Enabled
Enable Direction byte, Formats D0-
D3 only
1 = Direction Character Enabled
Enable Direction byte, Formats D0-
D3 only
92
0x5C Format D Zero Report
2 – Serial Port Configuration
0
232
only
--
--
0 = Disabled
1 = Enabled
Active only if setting 93 is enabled.
With no target, sends zero every two
seconds.
1 = Enabled
Active only if setting 93 is enabled.
With no target, sends zero every two
seconds.
93
0x5D
Format D Update on
Change Only
Change Only
2 – Serial Port Configuration
0
232
only
--
--
0 = Disabled
1 = Enabled
Enables speed reporting only when
the speed changes.
Active for Serial Formats D0-D4 only
1 = Enabled
Enables speed reporting only when
the speed changes.
Active for Serial Formats D0-D4 only
98
0x62
Zeros After Target Loss
2 – Serial Port Configuration
2
232
only
--
--
0 = No Zeros
1 = One Zero
2 = Stream Zeros
1 = One Zero
2 = Stream Zeros
99
0x63
Keep TX On with Target
9 – TX Power Save
0
--
--
0 = Disabled
1 = Enabled
If enabled, the TX On Time (64) is
extended as long as a target is
present.
1 = Enabled
If enabled, the TX On Time (64) is
extended as long as a target is
present.
100
0x64
Max TX On Time
9 – TX Power Save
0
--
--
0-60000 ms
If Keep TX On with Target (99) is
enabled, this setting forces the
transmitter off after the set time even
if a target is present. When set to 0,
Max TX time is infinite – the
transmitter is never forced off as
long as a target is present.
If Keep TX On with Target (99) is
enabled, this setting forces the
transmitter off after the set time even
if a target is present. When set to 0,
Max TX time is infinite – the
transmitter is never forced off as
long as a target is present.
116
0x74
Speed Sensor Address
11 - System
2
2
2
2 – 254 (0x02 – 0xFE)
Only for Stationary 485 model
Only for Stationary 485 model