Garmin International Inc 01337 Manual De Usuario

To install the ECU, mount it to your boat, connect it to the pump and to the CCU, and wire it to the boat battery.

Mount the ECU horizontally on a flat surface within 19 in. (.5 m) of the pump. the cables from the pump cannot be extended. 

Mount the ECU in a location where you can run wire to the boat battery, but do not connect it to the battery at this time. The power 

wire can be extended, if necessary. Use the table on 

 to determine the correct type of wire for extending the battery cable.

1.  Determine the best location for the ECU on your boat, satisfying the wiring considerations.
2.  Determine the correct type of screws for the mounting surface. Mounting screws are included with the ECU, but you may need to 

provide different screws if the supplied screws are not suitable for the mounting surface.

3.  Use the mounting template provided on 

. Tape the template to the mounting location and use a center punch and hammer 

to mark the pilot-hole locations.

4.  Drill pilot holes at the four mounting locations. 
5.  Use screws to mount the ECU.

Connect the two wires from the pump to the connectors marked PUMP and ENCODER on the ECU. The connectors are keyed to the 

appropriate fittings on the wires. Do not connect the eCu to power until all the connections of the entire GHP 10 system have 

been completed (

). Wait to connect the CCU/ECU interconnect cable until you have mounted the CCU by following the 

procedures in the next section.

Install the CCU by mounting it to your boat, connecting it to the ECU and to a NMEA 2000 network, and wiring it to the Shadow 

Drive, to the tachometer of your boat, to the alarm buzzer, and to the yellow CCU signal wire on the GHC 10.

Mount the CCU on the boat by using the included bracket. The CCU bracket has two portions, the mounting portion and the securing 

portion. Install the mounting portion on the mounting surface, and secure the CCU in the bracket with the securing portion.

Mount the CCU in the forward half of the boat, no higher than 10 ft. (3.05 m) above the waterline. 
You can mount the CCU below the waterline, as long as it is not in a location where it will be submerged or exposed to wash-down.
Mount the CCU bracket on a vertical surface or under a horizontal surface, so that the connected wires hang straight down.
Do not mount the CCU near magnetic material, magnets (speakers and electric motors), or high-current wires.
Mount the CCU at least 24 in. (0.6 m) away from movable or changing magnetic disturbances such as anchors, anchor chain, 

wiper motors, tool boxes, and the autopilot pump. 
Use a handheld compass to verify the absence of magnetic interference. If the handheld compass does not point north when you 

hold it in the location you want to mount the CCU, then there is magnetic interference. Choose another location and test again.
If possible, mount the CCU within 9

1

/

2

 ft. (3 m) of the ECU. If you cannot mount the CCU within 9

1

/

2

 ft. (3 m) of the ECU, 

extensions are

 available in lengths of 16

1

/

2

.)

1.  Determine the best location for the CCU on your boat. Use a handheld compass to be 

sure that the location is free of magnetic interference.

2.  Determine the correct type of screws for the mounting surface. Mounting screws are 

included with the CCU, but you may need to provide different screws if the supplied 

screws are not suitable for the mounting surface.

3.  Use the mounting template provided on 

. Be sure to install the mounting 

portion of the bracket with an opening at the bottom. Tape the template to the mounting 

location and use a center punch and hammer to mark the pilot-hole locations.

4.  Drill pilot holes at the three mounting locations. 
5.  Use screws to secure the mounting portion of the CCU bracket. 

•
•
•
•
•

•

•

screws (×)

screws (×)