Crestron Electronics Inc CWD1012 Manual De Usuario
Two-Way RF Transceiver Module
Crestron MNET-CWD1012
4
• Two-Way RF Transceiver Module: MNET-CWD1012
Hardware Guide - DOC. 6137
Antenna
This SMA non-standard male antenna port is located at edge of the circuit board for
attaching the included dipole antenna.
attaching the included dipole antenna.
APPROVED ANTENNAS:
The MNET-CWD1012 antenna interface has a unique coupling designed to ensure
that no antenna other than the one supplied shall be used with the device.
Replacement antennas may be purchased from Crestron according to the following
description:
Part Number: ANXX2400R00MHZ-2
Description: ANTENNA, 2400.00MHZ, DIPOLE, SMA, REVERSE POLARITY,
The MNET-CWD1012 antenna interface has a unique coupling designed to ensure
that no antenna other than the one supplied shall be used with the device.
Replacement antennas may be purchased from Crestron according to the following
description:
Part Number: ANXX2400R00MHZ-2
Description: ANTENNA, 2400.00MHZ, DIPOLE, SMA, REVERSE POLARITY,
FEMALE
Industry Compliance
Labeling Requirements
If the FCC ID on the MNET-CWD1012 is not visible when the module is installed
inside another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. This exterior
label can use wording such as the following: “Contains Transmitter Module FCC ID:
EROCWD1012” or “Contains FCC ID: EROCWD1012.” Any similar wording that
expresses the same meaning may be used.
If the FCC ID on the MNET-CWD1012 is not visible when the module is installed
inside another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. This exterior
label can use wording such as the following: “Contains Transmitter Module FCC ID:
EROCWD1012” or “Contains FCC ID: EROCWD1012.” Any similar wording that
expresses the same meaning may be used.
Compliance Statement (Part 15.19 )
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
Warning (Part 15.21 )
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
RF Exposure (OET Bulletin 65 )
To comply with FCC RF exposure requirements for mobile transmitting devices, this
transmitter should only be used or installed at locations where there is at least 20cm
separation distance between the antenna and all persons.
To comply with FCC RF exposure requirements for mobile transmitting devices, this
transmitter should only be used or installed at locations where there is at least 20cm
separation distance between the antenna and all persons.
Industry Canada Statement
The term "IC" before the certification/registration number only signifies that the
Industry Canada technical specifications were met.
IC: 5683A-CWD1012
The term "IC" before the certification/registration number only signifies that the
Industry Canada technical specifications were met.
IC: 5683A-CWD1012
Antenna Requirements:
The module must be installed such that the antenna connector is accessible for direct
antenna connection in the final configuration. If any cable or antenna other than that
provided with the MNET-CWD1012 is used, then the FCC authorization is no longer
considered valid and the FCC ID cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for reevaluating the end
product (including the transmitter) and obtaining a separate FCC authorization.
The module must be installed such that the antenna connector is accessible for direct
antenna connection in the final configuration. If any cable or antenna other than that
provided with the MNET-CWD1012 is used, then the FCC authorization is no longer
considered valid and the FCC ID cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for reevaluating the end
product (including the transmitter) and obtaining a separate FCC authorization.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with