Crestron Electronics Inc HTT-B2EX Manual De Usuario
1
quickstart guide
HTT-B2EX-BATT
www.crestron.com
888.273.7876
201.767.3400
Specifications subject to
change without notice.
HTT-B2EX-BATT
For Regulatory Compliance information, refer to the latest
version of Doc. 7451.
QUICKSTART DOC. 7450 (2036667) 05.13
QUICKSTART DOC. 7450 (2036667) 05.13
Battery-Powered infiNET EX 2-Button Wireless Keypad
1
The HTT-B2EX-BATT is a battery-powered, 2-button, wireless keypad
designed to control a wide range of applications supported by a
Crestron
®
control system. Compact and simplistic in design, the
HTT-B2EX-BATT is an ideal tabletop keypad for use as a hotel bedside
controller, a conference room presenter selector or a simple living
room lighting/shade controller. The HTT-B2EX-BATT is powered by
lithium coin cell batteries that boast high performance and a long
battery life. Outfitted with Crestron infiNET EX
®
technology, the
HTT-B2EX-BATT can be wirelessly connected to a Crestron control
system.
The HTT-B2EX-BATT is available with an optional tether that allows
The HTT-B2EX-BATT is available with an optional tether that allows
the device to be secured at its mounting location.
infiNET EX Communication
Built on steadfast infiNET™ technology, infiNET EX is the new
infiNET EX Communication
Built on steadfast infiNET™ technology, infiNET EX is the new
standard in 2-way wireless connectivity that can handle installations in
even the most urban settings. The redundant nature of its mesh
networking technology means that a command will never be missed,
resulting in faultless operation—something that is of the utmost
importance when it comes to home automation. The HTT-B2EX-BATT
harnesses this cutting edge wireless connectivity which affords it a
level of robustness and dependability above other solutions.
Description
Installation of the HTT-B2EX-BATT is limited to powering the device,
placing it on a flat surface and securing it to the line cord of a lamp
(optional).
Power Device
The HTT-B2EX-BATT is shipped with the batteries pre-installed. To power
Power Device
The HTT-B2EX-BATT is shipped with the batteries pre-installed. To power
the device pull and remove the plastic tab on the side of the device. Once
the plastic tab is removed the device is powered and ready to be operated.
Properly discard the plastic tab.
Place Device
Place the HTT-B2EX-BATT on the table surface where it is to be used.
Secure Device (Optional)
Place Device
Place the HTT-B2EX-BATT on the table surface where it is to be used.
Secure Device (Optional)
A security tether is available on the HTT-B2EX-BATT-B-T W/TETHER and
HTT-B2EX-BATT-W-T W/TETHER. The tether is secured inside the cover
of the keypad and attaches to a lamp cord. Use the following steps to
secure the loose end of the tether to a lamp cord.
1. Wrap the loose end of the tether around the lamp cord. The loop
should be loose enough to allow the tether to slide along the lamp
cord but not loose enough to slide it over the plug.
2. Use the supplied metal crimp and a pair of pliers to secure the tether
to the lamp cord.
3. Neatly trim the excess wire from the tether using a pair of wire cutters.
2
Installation
4
Firmware
It is recommended to use Crestron Toolbox™ to set the RF ID of the
device while the device is awake. Wake the device by pressing the large
or small button on the HTT-B2EX-BATT.
The RF ID of the unit, set using Crestron Toolbox, must match the RF ID
The RF ID of the unit, set using Crestron Toolbox, must match the RF ID
specified in the Crestron Studio™ or SIMPL Windows program.
3
RF ID
The device connects to the Crestron network via the infiNET EX
communications protocol. Use the procedures outlined below to join
or leave an infiNET EX network and to verify communications
between the device and the control system.
Joining an infiNET EX Network
Before a device can be used in a lighting system, it must first join an
Joining an infiNET EX Network
Before a device can be used in a lighting system, it must first join an
infiNET EX network by being acquired by an infiNET EX gateway.
NOTE: A device can be acquired by only one gateway.
1. Put the infiNET EX gateway into Acquire mode from the unit
itself or from Crestron Toolbox, as described in the latest version
of its manual, which is available from the Crestron Web site
(www.crestron.com/manuals).
NOTE: In an environment where multiple gateways are
installed, only one gateway should be in Acquire mode at any
time.
(Continued on the following page)
5
Wireless Communication
Lamp
Cord
Tether
Metal
Crimp
13/16 in
(21 mm)
Ø2 23/32 in
(69 mm)
Small
Button
Small Button
LED
Large
Button
Large Button
LED
To upgrade the firmware on the HTT-B2EX-BATT use Crestron
Toolbox (v. 2.37.01 or later). Upload firmware with the infiNET EX
Firmware Upload tool by clicking
Tools | infiNET EX Firmware
Upload in Crestron Toolbox.
NOTE: This infiNET EX Firmware Upload tool eliminates the need
for the user to manually wake every sensor that is being updated.
NOTE: When using the infiNET EX Firmware Upload tool, the
NOTE: When using the infiNET EX Firmware Upload tool, the
device does not update immediately. It updates upon waking up
and communicating with the gateway.
The infiNET EX Firmware Upload tool has four columns: product ID,
Firmware image, model name, and version number. Assign the
selected firmware image from the bottom box to the corresponding
ID/model name.
After pressing the load firmware file button, the gateway holds the
After pressing the load firmware file button, the gateway holds the
file and waits for the device to wake up on its own. Once the device
wakes up it checks for differences in the firmware file, if different
than the one currently on the device the firmware is loaded onto the
sensor.