Bosch Security Systems Inc. 0407-6 Manual De Usuario
Page 2
Copyright © 1998 Detection Systems, Inc. RF835 TriTech Installation Instructions
3.9 Mount the Detector
3.10 Set the Vertical Adjust
3.11 Set the PIR Sensitivity
3.14 Adjust the Microwave
3.16 Coverage
Patterns
Feet
0
5
10
15
20
25
30
35
0
5
10
15
20
5
10
15
20
0
Meters
1.6
3.2
4.8
6.4
8
9.6
11.2
B
C
D
E
H
I
J
K
N
O
P
Q
R
S
T
U
W
X
TOP VIEW
LZ
F
G
L
Z
10
0
Feet
0
5
10
15
20
25
30
-5°
SIDE VIEW
0
Meters
1.6
3.2
4.8
6.4
8
9.6
35
1
Remove masking for Look Down zone.
B-L
N-Q
R-U,Z
W-X
LZ
B CDE F G H I J K L
N R
W
S O Z P T X UQ
RF835 TriTech Lens
Pattern Testing in Walk Test Mode
Removing and replacing the cover will start a 90 second Walk
Test Mode. During this Test Mode, any activity in the sensor’s cov-
erage pattern will cause a transmitted alarm and LED activation.
Each alarm will also extend the Test Mode for an additional 90
seconds.
Test Mode. During this Test Mode, any activity in the sensor’s cov-
erage pattern will cause a transmitted alarm and LED activation.
Each alarm will also extend the Test Mode for an additional 90
seconds.
6.0 Other Information
Maintenance: At least once a month, the range and coverage
should be verified using the walk test mode. To ensure continual
daily operation, the end user should be instructed to walk through
the far end of the coverage pattern. This ensures an alarm output
prior to arming the system.
should be verified using the walk test mode. To ensure continual
daily operation, the end user should be instructed to walk through
the far end of the coverage pattern. This ensures an alarm output
prior to arming the system.
Pattern Masking: The PIR coverage pattern may be masked
using the masking stickers provided with the unit.
using the masking stickers provided with the unit.
NOTE: Masking only eliminates the PIR portion of the coverage
and has no effect on the Microwave pattern.
U.S. Patent Numbers: #4,660,024, #4,764,755, #5,077,548,
#5,208,567, #5,262,783, and #5,450,062. Other patents pending.
#5,208,567, #5,262,783, and #5,450,062. Other patents pending.
FCC Notice
This device complies with Part 15 of the FCC Rules and with RSS-210 of
Industry and Science Canada. Operation is subject to the following two con-
ditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that
may cause undesirable operation. Changes or modifications not expressly
approved by Detection Systems, Inc. can void the user's authority to operate
the equipment.
This device complies with Part 15 of the FCC Rules and with RSS-210 of
Industry and Science Canada. Operation is subject to the following two con-
ditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that
may cause undesirable operation. Changes or modifications not expressly
approved by Detection Systems, Inc. can void the user's authority to operate
the equipment.
Mounting
Range
Height
20 ft. (6.1 m)
35 ft. (10.7 m)
6.5 ft. (2 m)*
-7
-5*
7.0 ft. (2.1 m)
-9
-6
8.0 ft. (2.4 m)
-10
-7
* Required for pet immunity.
4.0 Programming
See your Control Panel Programming Guide for information.
5.0 Setup for Non-Pet Applications
Select the vertical starting angle from the chart. To adjust the vertical
starting angle for the desired mounting height and range, loosen
the vertical adjust screw and slide the board up, to point the PIR
pattern down. Note the settings on the vertical adjust scale (Figure
3.9).
starting angle for the desired mounting height and range, loosen
the vertical adjust screw and slide the board up, to point the PIR
pattern down. Note the settings on the vertical adjust scale (Figure
3.9).
NOTE: The vertical angle must be set at -5° for installations contain-
ing pets.
NOTE:
During the warm-up period, the tricolor LED will flash red until
the unit has stabilized (approximately 30 minutes) and has
seen no movement for two seconds. When the LED stops flash-
ing, the detector is ready to be tested. With no motion in the
protection area, the LED should be OFF. If the LED is on, re-
check the protection area for disturbances affecting the Micro-
wave (yellow) or PIR (green) technologies. (See Figure 3.11.)
the unit has stabilized (approximately 30 minutes) and has
seen no movement for two seconds. When the LED stops flash-
ing, the detector is ready to be tested. With no motion in the
protection area, the LED should be OFF. If the LED is on, re-
check the protection area for disturbances affecting the Micro-
wave (yellow) or PIR (green) technologies. (See Figure 3.11.)
3.15 Uncover Look Down Lens
3.12 LED Operation
LED Condition
Cause
Steady Red
Unit Alarm
Steady yellow
Microwave Activation (walk test)
Steady Green
PIR Activation (walk test)
Flashing Red
Warmup Period After Power-Up
Flashing Red (four-
pulse sequence)
Microwave or PIR failure.
Replace Unit.
3.13 Walk Test
Green =
PIR detect
PIR detect
Yellow =
MW detect
MW detect
Red =
Alarm
Alarm
Replace cover
Wait 30 minutes after installing
batteries to begin Walk test.
Wait 30 minutes after installing
batteries to begin Walk test.
INT
STD
- 6
- 10
MW
MIN
MAX
PIR
Sensitivity
Selection Pins
Sensitivity
Selection Pins
For pet applications,
set jumper to STD.
INT
STD
STD
INT
STD
STD
INT
STD
STD
INT
STD
- 6
- 10
MW
MIN
MAX
Peel away
the mask
In non-pet applications only, if look-down is
desired, peel away the
look-down mask.
Do not remove
the clear
plastic
lens.
INT
STD
MIN
MAX
MIN
MAX
Set Microwave to MIN
If necessary,
adjust the Microwave
Set as low
as possible for
normal operation
Loosen
the Vertical
Adjust Screw.
Adjust the board to - 5
(Refer to section 5.0)
INT
STD
Vertical Adjust Screw
- 6
- 10
- 6
- 10
MW
MIN
MAX
Thinwall
breakaway for
wall tamper
switch
Flush mount
Corner mount
Corner mount