DEI Headquarters Inc. DEI6867T Manual De Usuario

© 2017 Directed, All rights reserved.

N6867T--2017-11-30

1

Product Description

The 6867T control center is compatible with the following modules: DS4 

and DS4+.

Mounting the Control Center

Once this replacement control center has been installed, all 

remote controls must be paired with your system. See Remote 

Pairing for details and follow the instructions for your remote 

control type.

The control center’s position should be discussed with the vehicle owner 

prior to installation since the antenna, with built-in status LED and Valet/

Program, must be visible/accessible to the customer. 

The best position to locate the control center is centered high on the front 

windshield.  It can be mounted vertically or horizontally relative to the 

windshield.  Metallic window tint can also affect range negatively, so this 

should be a consideration when determining the mounting location.

After you determine the best mounting location, follow these steps: 

Clean the mounting area with a quality glass cleaner or alcohol to remove 

any dirt or residue. 

Plug the cable into the control center. 

Mount the control center with double-sided tape. 

Route the cable down the window pillar to the control module and plug 

the cable in the control module.

CONTROL CENTER

CABLE

CONTROL

MODULE

Remote Pairing

Prepare the vehicle system to be Paired with a new remote
1.

Open  at least one vehicle door.

2.

Turn the key to the ON position.

3.

Within 5 seconds  press and  release the Control button on the Control 
Center one time.

4.

Within 5 seconds,  press and  hold the Control button on the Control 
Center.  The status LED begins flashing in single flash sequence and 
the siren/horn sounds once to confirm the system is ready for remote 
pairing.  Release the button.

5.

Locate your remote control model below and follow the instructions.

System Pairing will exit if:
•

The ignition is turned off

•

The open door is closed

•

60 seconds lapses with no actions

Note

: Make sure the remote to be paired with the system is set for the de-

sired Car 1 or Car 2 operation. 

LCD Remote Control:
1.

Press and  hold the 

button for 8 seconds, the remote beeps once, 

Main Menu  is displayed.  Release the 

button.

2.

Press the AUX or 

 buttons until   Pair

 

is displayed.

3.

Press and  hold the 

button until the remote beeps 3 times then 

re-

lease the 

button. The remote is now ready to pair with the system.

4.

Press the 

 button.

5.

Wait  several seconds for feedback as the remote generates a security 
encryption and sends it to the Control Center. If pairing is successful 
the siren/horn sounds and the remote emits several tones. The screen 
displays if the Pairing is successful or failed with corresponding text. If 
pairing fails repeat step 4.

To exit pairing mode on the remote:
•  

Press and  release the 

A U 

X

button.

•

Wait  30 seconds without pressing a command button on the remote.

Responder LED or Companion Remote Control: 
1.   Press and  hold the 

button for 8 seconds. The transmit LED will come 

on solid.  Release the 

button.

2.   Press  and  hold  the 

  until  the  transmit  LED  flashes  3  times  then 

comes on solid.

3.

Press the 

 button.

4.

Wait  several seconds for feedback as the remote generates a security 
encryption and sends it to the Control Center. If pairing is successful 
the siren/horn sounds and the 2-way remote emits several tones (the 
companion  remote  does  not  generate  tones).  If  pairing  is  not  suc-
cessful press and release the 

button once and then repeat steps 

2 and 3.

To exit pairing mode on the remote:
•  

Press and  release the 

button once, then press and  hold until the 

transmit LED shuts off.

•

Wait  30 seconds without pressing a command button on the remote 
control. 

Digital Control Center