Visonic Inc. PWRMAXPRO Manual De Usuario

18 

DE5468IP 

4.5 DEFINING COMMUNICATION PARAMETERS 

Preliminary Guidance 

This mode allows you to adapt the telephone 

communication parameters to the local requirements.  

Significance  

⇒

⇒

 <1>  Inserts an asterisk (J)  

⇒

⇒

⇒

⇒

 

 

To enter a series of digits, use the following keys: 
<Numeric keypad> - to enter the number 

 - moves the cursor from left to right  

 - moves the cursor from right to left 

 - deletes everything after the cursor (to the right). 

4.5.1 Autotest Time 

(fig. 4.5, location 01)

 

Here you determine the time at which the telephone line 

will be tested and reported to the central station. 

4.5.2 Autotest Cycle 

(fig. 4.5, location 02)

 

Here you determine the time interval between consecutive 

telephone line test messages sent to the central station. 

The control panel performs this at regular intervals to verify 

proper communications.  

The options are: test every 1, 5, 7, 14, 30 days and test off. 

4.5.3 Area Code 

(fig. 4.5, location 03)

 

Here you enter the system tel. area code (up to 4 digits). 

4.5.4 Out Access No 

(fig. 4.5, location 04)

 

Here you enter the number that is used as a prefix to 

access an outside telephone line (if exists). 

4.5.5 First Central Station Tel. 

(fig. 4.5, loc. 05)

  

Here you program telephone number of the 1

st

 central station 

(including area code, 16 digit max) to which the system will 

report the event groups defined in memory location 11 (see 

note in fig. 4.5). 

4.5.6 First Account No. 

(fig. 4.5, location 06)

 

Here you enter number that will identify your specific alarm 

control system to the first central station. The number 

consists of 4 or 6 hexadecimal digits (see note in fig. 4.5). 

4.5.7 2

ND

 Central Station Tel

.

 

(fig. 4.5, loc. 07) 

Here you program telephone number of the 2

nd

 central station 

(including area code, 16 digit max) to which the system will 

report the event groups defined in memory location 11 (see 

note in fig. 4.5). 

4.5.8 Second Account No. 

(fig. 4.5, loc. 08)

 

Here you enter number that will identify your system to the 

2

nd

 central station. The account number consists of 4 or 6 

hexadecimal digits (see note in fig. 4.5). 

4.5.9 Report Format 

(fig. 4.5, location 09)

 

Here you select the reporting format used by the control panel 

to report events to central stations (see note in figure 4.5). 

The options are:   Contact-ID   SIA   4/2 1900/1400   

4/2 1800/2300   Scancom (see Appendix C - code lists). 

4.5.10 4/2 Pulse Rate 

(fig. 4.5, location 10)

 

Here you select the pulse rate at which data will be sent to 

central stations if any one of the 4/2 formats has been 

selected in Location 09 REPORT FORMAT (see note in 

fig. 4.5). The options are: 10, 20, 33 and 40 pps. 

4.5.11 Reporting to Central Stations 

(fig. 4.5, location 11) 

(see note in fig. 4.5). 

Here you determine which types of event will be reported 

to central stations. Due to lack of space in the display, 

abbreviations are used: alarm is “alrm”, alert is “alrt” and 

open/close is “o/c”. The asterisk (J) is a separator 

between events reported to central station 1 and events 

reported to central station 2. 

Messages are divided by type into three groups: 
GROUP  

EVENTS REPORTED 

Alarms 

Fire, Burglary, Panic, Tamper 

Open/Close  Arming AWAY, Arming HOME, Disarming  

Alerts 

No-activity, Emergency, Latchkey 

"Alarm" group has the highest priority and "Alert" group 

has the lowest priority.  
The selectable options are as follows: 

 

all -o/c J backup  All but open/close  All but open/close if center 1 

doesn’t respond 

all J all 

All  

All 

all-o/c J all -o/c  

All but open/close  All but open/close 

all –o/c J o/c  

All but open/close  Open/close 

all (–alrt) J alrt 

All but alerts 

Alerts 

Alrm J all (–alrm)  Alarms 

All but alarms 

Nothing Nothing 

all J backup 

All 

All if cent. 1 doesn’t respond 

4.5.12 Report CNF Alarm 

(fig. 4.5, location 12)

 

Here you determine whether the system will report whenever 

2 or more events (confirmed alarm) occur during a specific 

period (see par. 4.4.33 and note in figure 4.5).  

Available

 

options

 

are:

 

report,  disable report, 

enable + bypass (enabling report and bypassing the 

detector - applicable to PowerMax Pro that is compatible 

with DD423 standard). 

4.5.13 Send 2WV Code 

(fig. 4.5, location 13)

 

Here you determine whether the system will send two-way 

voice code to the central station (to turn the central station 

from data communication to voice communication state) by 

using pre-selected SIA or Contact-ID communication format 

only (see note in fig. 4.5). Options: send and don't send. 

4.5.14 Two-Way Voice Central Stations 

(fig. 4.5, loc. 14). (See note in fig. 4.5). 
Here you select the timeout for 2-way voice communication 

with Central Stations, or enable the central station to ring 

back for 2-way voice function. This option is applicable only 

after reporting an event to the central station. (The central 

station person can press [3] for listen-in", [1] for "speak out" 

or [6] for listening and speaking). 

The options are: 10, 45, 60, 90 seconds, 2 minutes, ring 

back and disable (no two-way voice communication).