ViewSonic Corporation AV802G Manual De Usuario
STATEMENT FOR MODUAL APPROVAL
This product is sold to OEM integrators only. The manual for the OEM integrators must include some instructions to be
followed by the end users in the user manual. For example:
The OEM integrators must be instructed to ensure that the end user has no manual instructions to remove or install the
device.
The OEM integrators must be instructed about the end product labeling ("Contains FCC ID:GSSAV802G, IC:
4280A-AV802G ")
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as the 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is
still responsible for testing their end product for any additional compliance requirements required with this module
installed (for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or
co-location with another transmitter), then the FCC and IC authorization is no longer considered valid and the FCC and
IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a separate FCC and IC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be
maintained between the antenna and users (for example, access points, routers, wireless ADSL modems, wireless media
adapter, wireless media gateway, and similar equipment). The final end product must be labeled in a visible area with the
following: " Contains FCC ID:GSSAV802G, IC: 4280A-AV802G ".
Manual Information for OEM integrator
Following RF exposure info shall be supplied in end-users manual depends on the application.
For mobile configuration of RF Exposure Information:
IMPORTANT NOTE:
To comply with FCC and IC RF exposure compliance requirements, this grant is applicable to only Mobile
Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at
least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or
transmitter
followed by the end users in the user manual. For example:
The OEM integrators must be instructed to ensure that the end user has no manual instructions to remove or install the
device.
The OEM integrators must be instructed about the end product labeling ("Contains FCC ID:GSSAV802G, IC:
4280A-AV802G ")
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as the 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is
still responsible for testing their end product for any additional compliance requirements required with this module
installed (for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or
co-location with another transmitter), then the FCC and IC authorization is no longer considered valid and the FCC and
IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a separate FCC and IC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be
maintained between the antenna and users (for example, access points, routers, wireless ADSL modems, wireless media
adapter, wireless media gateway, and similar equipment). The final end product must be labeled in a visible area with the
following: " Contains FCC ID:GSSAV802G, IC: 4280A-AV802G ".
Manual Information for OEM integrator
Following RF exposure info shall be supplied in end-users manual depends on the application.
For mobile configuration of RF Exposure Information:
IMPORTANT NOTE:
To comply with FCC and IC RF exposure compliance requirements, this grant is applicable to only Mobile
Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at
least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or
transmitter