Seiko Epson Corporation DGE001 Manual De Usuario
6. EXPORTING
S4E16400/S4E16401 Technical Manual
EPSON
33
(Rev.1.1)
5.4 Taiwan
This product (or module) is compliant with the “Administrative Regulations on Low Power Radio Waves
Radiated Devices” and “Low-power Radio-frequency Devices Technical Regulations (LP0002)”.
The following device handling instructions shall be followed.
Article 12. Without permission granted by the DGT, any company, enterprise, or user is not allowed to
Article 12. Without permission granted by the DGT, any company, enterprise, or user is not allowed to
change frequency, enhance transmitting power or alter original characteristic as well as performance to a
approved low power radio-frequency devices.
approved low power radio-frequency devices.
Article 14. The low power radio-frequency devices shall not influence aircraft security and interfere legal
communications; if found, the user shall cease operating immediately until no interference is achieved. The said
legal communications means radio communications is operated in compliance with the Telecommunications Act.
The low power radio-frequency devices must be susceptivle with the interference from legal communications or
ISM radio wave radiated devices.
legal communications means radio communications is operated in compliance with the Telecommunications Act.
The low power radio-frequency devices must be susceptivle with the interference from legal communications or
ISM radio wave radiated devices.
We recommend that you clearly specify describe notes on the following points in the instruction manual of
built-in products.
Permission No.
CCAB08LPxxxOTY
6. EXPORTING
6.1 Notes on Exporting to US
The primary and built-in products of this product (module) fall under the category of intentional and
unintentional radiation devices regulated in US.Check that the product is compliant with the following
standards before exporting it for the sale in US.
standards before exporting it for the sale in US.
♦
Required approval As of February, 2008
Finished devices embedded with this product require approval from FCC authorities concerned as
Finished devices embedded with this product require approval from FCC authorities concerned as
intentional and unintentional radiation devices. You need to have an official authentication authority
certify that the product conforms to the following standard to get a license.
(1) Intentional radiation device standard
certify that the product conforms to the following standard to get a license.
(1) Intentional radiation device standard
FCCpart15 Subpart C
(2) Unintentional radiation device standard
FCCpart15 Subpart B
(3) Product Safety Standard
UL standard (varies depending on the device)
Since this product has already acquired the certificate of conformance of (1), you do not need to aquire a new
certificate of conformance of (1) for finished goods containing this product (except for the case where a
technology to which the Intentional radiation device standard applies). You need to clearly describe notes on (1)
in the specified method on the finished goods or in the instruction manual.
technology to which the Intentional radiation device standard applies). You need to clearly describe notes on (1)
in the specified method on the finished goods or in the instruction manual.
Example of the sentense:
低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機、非經許可、公司、商號或使用者均不得擅自
變更頻率、加大功率或變更原設計之特性及功能。
變更頻率、加大功率或變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象
時、應立即停用，並改善至無干擾時方得繼續使用。
前項合法通信、指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干
擾。
時、應立即停用，並改善至無干擾時方得繼續使用。
前項合法通信、指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干
擾。