Digital Monitoring Products Inc 1100 Manual De Usuario
1100 Receiver Installation Sheet
Digital Monitoring Products
3
Programming the Panel
Before operating the 1100 Receiver, you must program the panel to recognize the 1100 Receiver. Enter panel
programming and press the COMMAND key to display Wireless Options. Program the 1100 Receiver and keyfobs in
this portion of panel programming.
programming and press the COMMAND key to display Wireless Options. Program the 1100 Receiver and keyfobs in
this portion of panel programming.
WIRELESS OPTIONS
Wireless
Options
Press the COMMAND key until Wireless Options displays. Press any top row Select Key
to enter Wireless Options programming.
to enter Wireless Options programming.
RECEIVER ID:
Receiver
IdentiÞ cation
Ensure the XR500 panel is set for wireless operation. Refer to XR500 Panel Wireless
Wiring on the previous page. The panel senses and automatically displays the receiver
identiÞ cation number. Press the COMMAND key to accept the Receiver ID and display
the check-in time prompt.
Wiring on the previous page. The panel senses and automatically displays the receiver
identiÞ cation number. Press the COMMAND key to accept the Receiver ID and display
the check-in time prompt.
CHECKIN: 30
30 60 120 180
Check-in
Time
The 1100 Receiver tells the 1101 Transmitter how long the transmitter waits before
checking in with the Receiver. Select the number of seconds the 1100 Receiver sends
to the transmitter to indicate the Check-in Time. Press any Select Key to change the
Check-in Time. Enter the number of seconds for the transmitter to wait. The default
is 30 seconds. Press the COMMAND key to accept the Check-in Time and display the
keyfobs programming prompt.
checking in with the Receiver. Select the number of seconds the 1100 Receiver sends
to the transmitter to indicate the Check-in Time. Press any Select Key to change the
Check-in Time. Enter the number of seconds for the transmitter to wait. The default
is 30 seconds. Press the COMMAND key to accept the Check-in Time and display the
keyfobs programming prompt.
KEYFOB
1
Keyfob
1
Use the following prompts to program up to four keyfobs to use with this receiver.
Press any Select Key to enter Keyfob 1 Programming.
Press any Select Key to enter Keyfob 1 Programming.
SERIAL NO:
Serial
Number
Enter the keyfob serial number located on the casing back. Each keyfob has a unique
serial number. Do not lose the serial number. Do not use the same serial number
for more than one keyfob. Press the Back Arrow key to make corrections. Press the
COMMAND key to accept the serial number and display the Output Number option.
serial number. Do not lose the serial number. Do not use the same serial number
for more than one keyfob. Press the Back Arrow key to make corrections. Press the
COMMAND key to accept the serial number and display the Output Number option.
OUTPUT NO: 0
Output
Number
The fourth button on the keyfob is programmed to trip an output. Enter the output
number that this keyfob trips when pressed. For example, the output number could
be the output that controls the garage door opener. Press the Back Arrow key to
make corrections. Press the COMMAND key to accept the output number and begin
programming the next keyfob. After programming all keyfobs, press the COMMAND key
to exit Wireless Options programming.
Note: These prompts repeat for Keyfob 2, Keyfob 3, and Keyfob 4. Repeat these
programming options for each keyfob used in the system.
Program transmitters in panel programming Zone Information.
number that this keyfob trips when pressed. For example, the output number could
be the output that controls the garage door opener. Press the Back Arrow key to
make corrections. Press the COMMAND key to accept the output number and begin
programming the next keyfob. After programming all keyfobs, press the COMMAND key
to exit Wireless Options programming.
Note: These prompts repeat for Keyfob 2, Keyfob 3, and Keyfob 4. Repeat these
programming options for each keyfob used in the system.
Program transmitters in panel programming Zone Information.
XR500 Programming
After programming Wireless Options and all the keyfobs save the information. Press the COMMAND key until STOP
displays. Press any top row Select Key to run the Stop routine. When any panel programming is changed, the Stop
routine must run and "SAVING PROGRAM" must displays on the keypad in order to save the programming changes.
After programming Wireless Options and all the keyfobs save the information. Press the COMMAND key until STOP
displays. Press any top row Select Key to run the Stop routine. When any panel programming is changed, the Stop
routine must run and "SAVING PROGRAM" must displays on the keypad in order to save the programming changes.