Honeywell International Inc. 8DL5800CO Manual De Usuario
– 3 –
5800CO-003-V0
Figure 3. Mount Detector Across Ceiling Panel Support
DO NOT attach the detector to removable ceiling panels. Attach
the detector across panel support as shown in Figure 3.
the detector across panel support as shown in Figure 3.
CAUTION
Airborne dust particles can enter the detector. Honeywell
recommends the removal of detectors before beginning construction
or any other dust producing activity. Carbon monoxide detectors
are not to be used with detector guards unless the combination has
been evaluated and found suitable for that purpose.
Airborne dust particles can enter the detector. Honeywell
recommends the removal of detectors before beginning construction
or any other dust producing activity. Carbon monoxide detectors
are not to be used with detector guards unless the combination has
been evaluated and found suitable for that purpose.
LIVING
ROOM
BEDROOM
BEDROOM
BEDROOM
KITCHEN
TO
BR
BR
CLOSED
DOOR
DOOR
BASEMENT
GARAGE
CARBON MONOXIDE ALARM
LOCATION FOR MULTI-LEVEL RESIDENCE
LOCATION FOR MULTI-LEVEL RESIDENCE
–
5800CO-005-V0
Figure4. Detector Location Diagram
Tamper Protection
This detector has a built-in tamper switch that will cause a CHECK
signal to be displayed at the console of the alarm system if it is
removed from its mounting base. The 5800CO detector includes a
tamper-resistant feature that prevents removal from the mounting
base without the use of a tool. To engage the tamper-resistant
feature, cut the small plastic tab located on the mounting base
(Figure 2), and then install the detector. To remove the detector
from the base once it has been made tamper resistant, use a small
screwdriver to depress the square tamper release tab, located on
the skirt of the mounting base, and turn the detector
counterclockwise.
signal to be displayed at the console of the alarm system if it is
removed from its mounting base. The 5800CO detector includes a
tamper-resistant feature that prevents removal from the mounting
base without the use of a tool. To engage the tamper-resistant
feature, cut the small plastic tab located on the mounting base
(Figure 2), and then install the detector. To remove the detector
from the base once it has been made tamper resistant, use a small
screwdriver to depress the square tamper release tab, located on
the skirt of the mounting base, and turn the detector
counterclockwise.
TESTING THE DETECTOR
NOTE: Before testing, notify the central station that the detector
system is undergoing maintenance, in order to prevent unwanted
alarms. Testing the detector will activate an alarm and send a
signal to the panel.
system is undergoing maintenance, in order to prevent unwanted
alarms. Testing the detector will activate an alarm and send a
signal to the panel.
The manufacturer cannot recommend a specific agent with which
to test the detector.
to test the detector.
Detectors must be tested after installation and following periodic
maintenance.
maintenance.
Testing the Sensor
1.
A recessed test button is located on the detector housing (see
Figure 5).
Figure 5).
2.
Push and hold the recessed test button for a minimum of 5
seconds. Use a small screwdriver or Allen key with maximum
diameter of 0.18 inch (the alarm panel will trigger and then
the detector will go into alarm. If the tool is removed from the
recessed button the sounder will shut off.)
seconds. Use a small screwdriver or Allen key with maximum
diameter of 0.18 inch (the alarm panel will trigger and then
the detector will go into alarm. If the tool is removed from the
recessed button the sounder will shut off.)
If the detector is within the listed sensitivity limits, the LED
on the detector should blink once per second and the horn
should sound within 3 seconds.
on the detector should blink once per second and the horn
should sound within 3 seconds.
5800CO-004-V0
RED
LED
FLANGE
LOCK
SN
IP
O
FF
F
OR
TAM
PE
R L
OC
K
RECESSED
TEST
BUTTON
PUSH RECESSED
BUTTON WITH A
0.18" MAX.
DIAMETER TOOL
LEDs
Figure 5. Recessed Test Button Opening
Testing Signal Strength
NOTE: Remove battery tab before installation.
This test should be performed before installation to determine a
strong communication path with the control panel and after
installation is complete. Also, the owner/user should test the unit at
least weekly.
strong communication path with the control panel and after
installation is complete. Also, the owner/user should test the unit at
least weekly.
1.
Activate the wireless system’s GO/NO GO TEST mode from
the keypad.
the keypad.
2.
Depress and hold the detector’s TEST button. If the detector
has not previously detected a low battery condition and it is
within proper sensitivity limits, the detector should
immediately transmit an alarm signal to the control panel.
The built-in horn will start to sound about 2.5 seconds after
depressing the button.
has not previously detected a low battery condition and it is
within proper sensitivity limits, the detector should
immediately transmit an alarm signal to the control panel.
The built-in horn will start to sound about 2.5 seconds after
depressing the button.
3.
The wireless system’s keypad should emit at least three
audible sounds when the alarm transmission is received and
will display the transmitting detector’s zone number.
audible sounds when the alarm transmission is received and
will display the transmitting detector’s zone number.
4.
When the console has received the test signal, release the
TEST button. The horn will immediately stop and a few
seconds later the detector’s zone number will clear from the
console display.
TEST button. The horn will immediately stop and a few
seconds later the detector’s zone number will clear from the
console display.
5.
If the console does not respond as noted, check the polarity of
the battery and be sure it is fresh. If this is an initial
installation, try moving the detector to another location that
provides proper reception. Also be sure that the detector has
been “enrolled” by the control panel (see PROGRAMMING).
Then, repeat the test.
the battery and be sure it is fresh. If this is an initial
installation, try moving the detector to another location that
provides proper reception. Also be sure that the detector has
been “enrolled” by the control panel (see PROGRAMMING).
Then, repeat the test.
6.
Turn off the system’s TEST mode from the keypad (security
code + OFF).
code + OFF).
Testing Programmed Loops
This test should be performed before installation to ensure that the
detector has been programmed and is operational in the system.
detector has been programmed and is operational in the system.
1.
Activate the system’s TRANSMITTER ID SNIFFER mode
from the keypad (see the control panel’s instructions). All
programmed wireless zones will be displayed, one by one, on
the system keypad. Make sure the detector zone is displayed in
the sequence. (If not, recheck that the detector zone has been
properly programmed.)
from the keypad (see the control panel’s instructions). All
programmed wireless zones will be displayed, one by one, on
the system keypad. Make sure the detector zone is displayed in
the sequence. (If not, recheck that the detector zone has been
properly programmed.)
2.
With the detector mounted to the bracket, press the detector’s
TEST button. The zone associated with the detector should
disappear from the keypad on the next display cycle. This
means that the system has received a transmission from the
detector zone you programmed.
TEST button. The zone associated with the detector should
disappear from the keypad on the next display cycle. This
means that the system has received a transmission from the
detector zone you programmed.
3.
When testing is complete, enter the Installer code + the OFF
key to exit TEST mode.
key to exit TEST mode.
When all system testing has been completed, notify the central
station that the system is back on line.
station that the system is back on line.