Honeywell International Inc. 8DL6160RF Manual De Usuario
Preliminary - 6 September 2002
K0903ax 9/6/02
5).(<3$'75$16&(,9(5
INSTALLATION GUIDE
GENERAL INFORMATION
The 6160RF keypad/transceiver is a is a combination unit
that contains the following:
that contains the following:
•
A 6160 Alphanumeric Addressable Keypad
•
A 5881M RF Receiver
•
A 5800TM Transmitter Module
The 6160RF Keypad/Transceiver may be used on any
control panel that supports the 6160 Keypad (e.g., VISTA-
10SE, VISTA-15, VISTA-20SE, VISTA-40, VISTA-50P).
control panel that supports the 6160 Keypad (e.g., VISTA-
10SE, VISTA-15, VISTA-20SE, VISTA-40, VISTA-50P).
FEATURES
Wireless Features
•
Supports wireless key transmitters (5804, 5804BD).
•
Supports wireless keys with Signal Sentry (high-
security) (5804E).
•
Provides a nominal range of 200' for the RF
transmitters (some transmitters have a shorter range).
•
Supports RF jam detection when the receiver is enabled.
UL
The following transmitters are not intended for use in UL
installations: 5804, 5804BD, 5804BDV, 5804E and 5827BD.
installations: 5804, 5804BD, 5804BDV, 5804E and 5827BD.
Programming Features
•
Provides default settings for the functions of the
wireless keys.
wireless keys.
•
Provides a method to enroll up to eight (8) encrypted
(high security) devices.
Additional Features
•
Provides tamper protection that causes the system to
annunciate a trouble condition if the cover is removed.
(If supported by the control panel). The tamper switch
has not been evaluated for UL installation.
(If supported by the control panel). The tamper switch
has not been evaluated for UL installation.
•
Capable of sending status signals (Armed, Ready, etc.)
to bi-directional units such as 5804BD, 5804BDV and
5827BD.
5827BD.
APPLICATION GUIDELINES FOR THE 6160RF
Use the following guidelines when planning an
installation:
installation:
•
If using bi-directional devices, be sure to enable the
transmitter module in the 6160RF.
transmitter module in the 6160RF.
•
If transmitters are programmed into the control
panel, be sure to enable the receiver. (Make sure you
do not exceed the number of receivers supported by
the control panel.)
panel, be sure to enable the receiver. (Make sure you
do not exceed the number of receivers supported by
the control panel.)
•
You must set the House ID only if you are using RF
keypads and/or bi-directional devices; AND the House
ID Source is the 6160RF (Local).
keypads and/or bi-directional devices; AND the House
ID Source is the 6160RF (Local).
Note: If the House ID source is the panel, enter *99 into keypad.
6160RF Application Guide
The guide, provided below, outlines how to program the
wireless keys, RF receiver, and the House ID in the
6160RF for your particular installation.
wireless keys, RF receiver, and the House ID in the
6160RF for your particular installation.
*
Two 6160RFs are needed for this application: one connected to partition 1’s keypad terminals, and
one connected to partition 2’s.
one connected to partition 2’s.
** If using an RF keypad on only one partition, the 6160RF’s partition assignment must match the
partition set in field 1*48.
*** If set for Local on a partition control, the 6160RF’s partition assignment must match the one
programmed in the BD device.
Control Panel
RF keypads and/or
Bi-directional
devices on more
than 1 partition?
than 1 partition?
Program
RF Receiver
House ID
Source***
As
VISTA-10SE, VISTA-15,
VIA-30PSE
VIA-30PSE
NO Enable
System
VISTA-20SE
NO Enable
System
YES*
Disable
Local
VISTA-40, VISTA-50P
NO**
Enable
System
YES
Disable
Local