Williams Sound T27 Manual De Usuario
®
3
S
ETTING
U
P THE
PPA VP
þ
S
TEP
1: S
ELECT
L
OCATION
Position the PPA T27 transmitter near the sound system or mixer from which it will receive audio.
þ
S
TEP
2: I
NSTALL THE
A
NTENNA
Gently thread the ANT 021 rubber duckie antenna onto the stud recessed in the hole on the top of the
transmitter. Note: The antenna output on the back of the unit has been defeated, as specified by FCC
Rules. To use a remote antenna, contact your dealer or Williams Sound.
transmitter. Note: The antenna output on the back of the unit has been defeated, as specified by FCC
Rules. To use a remote antenna, contact your dealer or Williams Sound.
þ
S
TEP
3: C
ONNECT THE
P
OWER
Locate the power supply cord equipped with the 5-pin DIN connector, then plug the connector into
the “Power In” jack located in the back of the T27. Plug in the power supply into the AC outlet. On
power up, the number “8” will scroll across the T27 display 3 times while the system initializes. The
system will then display the default system frequency (72.9 MHz) or the last selected frequency set
by the user.
the “Power In” jack located in the back of the T27. Plug in the power supply into the AC outlet. On
power up, the number “8” will scroll across the T27 display 3 times while the system initializes. The
system will then display the default system frequency (72.9 MHz) or the last selected frequency set
by the user.
þ
S
TEP
4: S
ELECT THE
F
REQUENCY
The T27 has 17 available channels in the 72-76 MHz bandwidth. By default, the T27 frequency is
set to 72.900 MHz. To change the frequency on the T27, press and release the down “ ˇ “ or up “ ˆ “
set to 72.900 MHz. To change the frequency on the T27, press and release the down “ ˇ “ or up “ ˆ “
frequency selector button until the desired frequency is displayed. After 3 seconds of no activity, the
frequency selection will be set.
Check to make sure the receiver being used is operating on the same frequency as the trans-
mitter!
frequency selection will be set.
Check to make sure the receiver being used is operating on the same frequency as the trans-
mitter!
NOTE: You can LOCK this selection to prevent others from accidently changing the frequency.
To LOCK the frequency you have selected, press and hold both down “ ˇ ” and up “ ˆ ” frequency
selector buttons for 3 seconds until the word “Loc” appears on the display. The frequency is now
locked
selector buttons for 3 seconds until the word “Loc” appears on the display. The frequency is now
locked
. Should the user press the frequency selector button while in “Lock” mode, the word “Loc”
will be displayed for 2 seconds.
To UNLOCK the frequency selected, press and hold both down “ ˇ ” and up “ ˆ ” frequency selector
buttons for 3 seconds until the transmitter displays ”Un” then “Loc” on the display. The frequency is
now unlocked. The user is now free to change the frequeny channels on the T27 as needed.
To UNLOCK the frequency selected, press and hold both down “ ˇ ” and up “ ˆ ” frequency selector
buttons for 3 seconds until the transmitter displays ”Un” then “Loc” on the display. The frequency is
now unlocked. The user is now free to change the frequeny channels on the T27 as needed.
FIG 2: Features & Controls
Front View
Rear View
1. Mic input jack, 3.5 mm
2. Audio Level Indicator
3. Audio Level Control
2. Audio Level Indicator
3. Audio Level Control
4. Frequency Display (LED)
5. Frequency Selector,
5. Frequency Selector,
Lock/Unlock Control
6. Power Input jack, 12VAC
7. Antenna Connector, 75 Ohms
7. Antenna Connector, 75 Ohms
8. Audio input jack, RCA-type
(Line Level, Unbalanced)
(Line Level, Unbalanced)
1 2 3 4
5
6
7
8