Mindray DS USA Inc. WT0707-00000 Manual De Usuario
Patient Reports Tab
Report Functions
8 - 28
0070-10-0690-01
Panorama™ Operating Instructions
A WMTS 608 wireless bedside
device is in use.
device is in use.
No solution required.
The selected patient tile is
relearning phase, or is in a
Communications Lost or
Standby state.
relearning phase, or is in a
Communications Lost or
Standby state.
Wait for the patient tile to
resume monitoring.
resume monitoring.
The ST Report button is
hidden.
hidden.
The selected patient tile is in a
Waiting for Patient state.
Waiting for Patient state.
Activate the destination device.
The Print All Strips report
button is disabled.
button is disabled.
The selected patient tile is in a
Communications Lost or
Standby state.
Communications Lost or
Standby state.
Wait for the patient tile to
resume monitoring.
resume monitoring.
The Print All Strips button is
hidden.
hidden.
The selected patient tile is in a
Waiting for Patient state.
Waiting for Patient state.
Activate the destination device.
The report will not print
There are several reasons that
a report would not print. There
could be a communication
problem between the printer
and the Panorama Central
Station and/or there could be
a problem with the printer.
a report would not print. There
could be a communication
problem between the printer
and the Panorama Central
Station and/or there could be
a problem with the printer.
If there is an error that appears
such as Printer out of
Paper you will need to
remedy that situation.
If the No Printer connected
or Printer not Available
error is displayed, verify that
the printer was properly
configured with the Panorama
Central Station. Refer to the
Panorama Printer
Configuration Manual (P/N
0070-00-0561).
such as Printer out of
Paper you will need to
remedy that situation.
If the No Printer connected
or Printer not Available
error is displayed, verify that
the printer was properly
configured with the Panorama
Central Station. Refer to the
Panorama Printer
Configuration Manual (P/N
0070-00-0561).
The Delta T parameter does not
display in the All Strips report.
display in the All Strips report.
One of the two temperature
sources used to calculate the
Delta T value is not valid.
sources used to calculate the
Delta T value is not valid.
Verify that the two temperature
sources have been properly
configured.
sources have been properly
configured.
Page On Alarm column not
displayed in Patient Alarm
Report
displayed in Patient Alarm
Report
Paging option is not enabled at
the central station.
the central station.
If available, enable Paging
option. If feature unavailable,
no solution required.
option. If feature unavailable,
no solution required.
All Arrhythmia On/Off setting
set to Off
set to Off
Arrhythmia is disabled for a
selected patient tile.
selected patient tile.
If available, enable arrhythmia
for the selected patient tile. If
feature or license is
unavailable, no solution
required.
for the selected patient tile. If
feature or license is
unavailable, no solution
required.
In the Patient Alarm Report’s
Arrhythmia Settings section, a
“---” is displayed as the value
for Asystole Delay, V-Tach
Threshold, and V-Tach Rate
Arrhythmia Settings section, a
“---” is displayed as the value
for Asystole Delay, V-Tach
Threshold, and V-Tach Rate
Arrhythmia is disabled for a
selected patient tile.
selected patient tile.
If available, enable arrhythmia
for the selected patient tile. If
feature or license is
unavailable, no solution
required.
for the selected patient tile. If
feature or license is
unavailable, no solution
required.
Paging Delay Settings section
not displayed in the Patient
Alarm Report.
not displayed in the Patient
Alarm Report.
This section will only be
displayed when Paging is
enabled at the central station.
displayed when Paging is
enabled at the central station.
If available, enable Paging
option. If feature unavailable,
no solution required.
option. If feature unavailable,
no solution required.
MESSAGE/ISSUE *
REASON
SOLUTION
*
Messages are shown in all bold text.