Sanitag Technologies Corporation AT004H Manual De Usuario
Setting Up Devices & RF Netwowk
1-9
THIS DOCUMENT IS THE PROPERTY OF SANITAG COMPANY. IT MAY NOT BE COPIED AND REPRODUCED WITHOUT WRITTEN PERMISSION OF SANITAG
COMPANY. COPYRIGHT NOTICES MAY NOT BE REMOVED
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
1.1.6.
Active RFID Tag for New Staff/Doctors (Sanitag AT-004-H)
It has two leds (Green, Red) If device is powered up, Green led blinks by each
wake/sleep cycle. In stand-by mode, there is no led indication.It has two buttons (Orange,
Blue) with following functions:
wake/sleep cycle. In stand-by mode, there is no led indication.It has two buttons (Orange,
Blue) with following functions:
Orange Button Short Press/Release: Send Emergency Message / Wake-up the if
in stand-by
Orange Button Press for 5 Seconds: Enter to standby mode.
Blue button is used for matching mobile devices.
Sanitag AT-004-H device has 2.4GHz RF propagation that 2.5dBm output power level
and it has 2,4 GHz Pcb antenna. Also, AT-004-H device has UWB module that has 3.1 ~
8 GHz monopole antenna. We operation at 4.4GHz due to special reason. UWB Module
output power is fully adjustable from 0 dBm to 15.5 dBm via firmware.
The
and it has 2,4 GHz Pcb antenna. Also, AT-004-H device has UWB module that has 3.1 ~
8 GHz monopole antenna. We operation at 4.4GHz due to special reason. UWB Module
output power is fully adjustable from 0 dBm to 15.5 dBm via firmware.
The
device’s both of PCB antenna and UWB monopole antenna are omnidirectional. Both
of antenna are fixed on PCB
, that's why İt cannot change reorient and relocate.
Therefore AT-004-H
can take signal every direction. İf Sanitag AT-004-H obstructs by
obstacle of in Table 1. The
device’s RF signal will decrease as stated in Table 1.
AT-004-H can transmit until 200 meters to readers if RF output power is fully.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS.
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS
DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Warning: Changes or modifications not expressly approved by the party responsible for
SUBJECT TO THE FOLLOWING TWO CONDITIONS.
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS
DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.