Sanitag Technologies Corporation AT004H Manual De Usuario
Setting Up Devices & RF Netwowk
1-5
THIS DOCUMENT IS THE PROPERTY OF SANITAG COMPANY. IT MAY NOT BE COPIED AND REPRODUCED WITHOUT WRITTEN PERMISSION OF SANITAG
COMPANY. COPYRIGHT NOTICES MAY NOT BE REMOVED
user is encouraged to try to correct the interference by one or more of the following
measures:
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
—Consult the dealer or an experienced radio/TV technician for help.
1.1.2.
Active RFID Room Level Reader (Sanitag Model No: AR-001-HLR) &
Active RFID Long Range Reader (Sanitag Model No: AR-002-HLR)
Active RFID Long Range Reader (Sanitag Model No: AR-002-HLR)
These devices are hierarchically below Router or upper level Reader on network. It
collects Mobile Beacon Messages and also sub-level Reader messages and then routes
them to the upper level Reader or Router. It has also blue leds on itself.
If leds blink, it means that the reader device searches to join Rf network. So it implies that
the reader is not joined any Rf network yet.
If leds ligthen constantly, it means that the reader device joins Rf Network succesfully.
Sanitag AR-001-HLR device has RF propagation that 2.5dBm output power level and it
has 2,4 GHz uFl tranmitter antenna which is has 2dBi gain. Sanitag AR-002-HLR device
has RF propagation that 22dBm output power level and it has 2,4 GHz uFl tranmitter
antenna which is has 2dBi gain.
Also, AR-001-HLR and AR-002-HLR devices have UWB module that has 3.1 ~ 8 GHz
monopole antenna. We operation at 4.4GHz due to special reason. UWB Module output
power is fully adjustable from 0 dBm to 15.5 dBm via firmware.
The antenna that using on Sanitag AR-001-HLR and Sanitag AR-002-HLR are wire
antenna which is fixed on PCB, That's why İt cannot change reorient and relocate
collects Mobile Beacon Messages and also sub-level Reader messages and then routes
them to the upper level Reader or Router. It has also blue leds on itself.
If leds blink, it means that the reader device searches to join Rf network. So it implies that
the reader is not joined any Rf network yet.
If leds ligthen constantly, it means that the reader device joins Rf Network succesfully.
Sanitag AR-001-HLR device has RF propagation that 2.5dBm output power level and it
has 2,4 GHz uFl tranmitter antenna which is has 2dBi gain. Sanitag AR-002-HLR device
has RF propagation that 22dBm output power level and it has 2,4 GHz uFl tranmitter
antenna which is has 2dBi gain.
Also, AR-001-HLR and AR-002-HLR devices have UWB module that has 3.1 ~ 8 GHz
monopole antenna. We operation at 4.4GHz due to special reason. UWB Module output
power is fully adjustable from 0 dBm to 15.5 dBm via firmware.
The antenna that using on Sanitag AR-001-HLR and Sanitag AR-002-HLR are wire
antenna which is fixed on PCB, That's why İt cannot change reorient and relocate
.
The
device's antenna type is omnidirectional. Therefore, the Sanitag AR-001-HLR and
Sanitag AR-002-HLR can take signal every direction.
Sanitag AR-002-HLR can take signal every direction.
İf devices obstruct by obstacle of in
Table 1. The
device’s RF signal will decrease as stated in Table 1.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS.
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS
DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Warning: Changes or modifications not expressly approved by the party responsible for
SUBJECT TO THE FOLLOWING TWO CONDITIONS.
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS
DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide