Umain Inc. UMI-HST-S1M-CT Manual De Usuario
OEM INTEGRATION INSTRUCTIONS:
This device is intended only for OEM integrators under the following conditions:
This device is intended only for OEM integrators under the following conditions:
The module must be installed in the host equipment such that 20 cm is maintained between
the antenna and users, and the transmitter module may not be co-located with any other
transmitter or antenna. The module shall be only used with the internal on-board antenna
that has been originally tested and certified with this module. External antennas are not
supported. As long as these 3 conditions above are met, further transmitter test will not be
required.
the antenna and users, and the transmitter module may not be co-located with any other
transmitter or antenna. The module shall be only used with the internal on-board antenna
that has been originally tested and certified with this module. External antennas are not
supported. As long as these 3 conditions above are met, further transmitter test will not be
required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed (for example, digital
device emissions, PC peripheral requirements, etc.). The end-product may need
Verification testing, Declaration of Conformity testing, a Permissive Class II Change or new
Certification. Please involve a FCC certification specialist in order to determine what will be
exactly applicable for the end-product.
additional compliance requirements required with this module installed (for example, digital
device emissions, PC peripheral requirements, etc.). The end-product may need
Verification testing, Declaration of Conformity testing, a Permissive Class II Change or new
Certification. Please involve a FCC certification specialist in order to determine what will be
exactly applicable for the end-product.
Validity of using the module certification:
In the event that these conditions cannot be met (for example certain laptop configurations
or co-location with another transmitter), then the FCC authorization for this module in
combination with the host equipment is no longer considered valid and the FCC ID of the
module cannot be used on the final product. In these circumstances, the OEM integrator will
be responsible for re-evaluating the end product (including the transmitter) and obtaining a
separate FCC authorization. In such cases, please involve a FCC certification specialist in
order to determine if a Permissive Class II Change or new Certification is required.
In the event that these conditions cannot be met (for example certain laptop configurations
or co-location with another transmitter), then the FCC authorization for this module in
combination with the host equipment is no longer considered valid and the FCC ID of the
module cannot be used on the final product. In these circumstances, the OEM integrator will
be responsible for re-evaluating the end product (including the transmitter) and obtaining a
separate FCC authorization. In such cases, please involve a FCC certification specialist in
order to determine if a Permissive Class II Change or new Certification is required.
Upgrade Firmware:
The software provided for firmware upgrade will not be capable to affect any RF
parameters as certified for the FCC for this module, in order to prevent compliance issues.
The software provided for firmware upgrade will not be capable to affect any RF
parameters as certified for the FCC for this module, in order to prevent compliance issues.
End product labeling:
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final end
product must be labeled in a visible area with the following:
“Contains FCC ID: 2AN8QUMI-HST-S1M-CT”.
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final end
product must be labeled in a visible area with the following:
“Contains FCC ID: 2AN8QUMI-HST-S1M-CT”.
Information that must be placed in the end user manual:
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user's manual of the end product which
integrates this module. The end user manual shall include all required regulatory
information/warning as show in this manual.
how to install or remove this RF module in the user's manual of the end product which
integrates this module. The end user manual shall include all required regulatory
information/warning as show in this manual.