GUANGDONG GDA Valve Technology.Co.Ltd GH03-C Manual De Usuario
HEARTH MOUNT
The remote receiver can be placed on the fireplace hearth or under
the fireplace,behind the control access panel.Position where the
ambient temperature inside the receiver case does not exceed
130ºF.NOTE:Black Button is used on Hearth Mount Applications.
the fireplace,behind the control access panel.Position where the
ambient temperature inside the receiver case does not exceed
130ºF.NOTE:Black Button is used on Hearth Mount Applications.
WIRING INSTRUCTIONS
Make sure the remote receiver switch is in the OFF position.For best
results it is remommender that 18 gauge stranded wires should be
used to make connections and no longer than 50-feet.
results it is remommender that 18 gauge stranded wires should be
used to make connections and no longer than 50-feet.
This GH03-R remote receiver is to be connected
to a manual valve with a latching ON/OFF
solenoid
to a manual valve with a latching ON/OFF
solenoid
Connect two 18 gauge stranded or solid wires
from the remote receiver terminals to the latching
solenoid.(See figure to the right)
from the remote receiver terminals to the latching
solenoid.(See figure to the right)
IMPORTANT NOTE: Operation of this control is
dependent on which wire is attached to which
terminal.If operation of control does not
correspond to operating buttons on
transmitter,reverse wire installation at the receiver
or at the control.
dependent on which wire is attached to which
terminal.If operation of control does not
correspond to operating buttons on
transmitter,reverse wire installation at the receiver
or at the control.
GENERAL INFORMATION
COMMUNICATION-SAFETY-TRANSMITTER
This remote control has a COMMUNICATION-SAFETY function built into its software.It provides an extra
margin of safety when the TRANSMITTER is out of the normal 50-feet operating range of the receiver.
margin of safety when the TRANSMITTER is out of the normal 50-feet operating range of the receiver.
The COMMUNICATION-SAFETY feature operates in the following manner,in all OPERATING MODES-ON/ON
THERMO
THERMO
At all times and in all OPERATING MODES,the transmitter sends an RF signal every 2 minutes,to the
receiver,indicating that the transmitter is within the normal operating range of 50-feet.Should the receiver NOT
receive a transmitter signal every 2 minutes,the IC software,in the RECEIVER,will begin a 2-HOUR(120-
minute)countdown timing function.If during this 2-hour period,the receiver does not receive a signal from the
transmitter,the receiver will shut down the appliance being controlled by the receiver.The RECEIVER will then
emit a series of rapid”beeps”for a period of 10 seconds.Then after 10 seconds of rapid beeping,the RECEIVER
will continue to emit a single:”beep”every 4 seconds until a transmitter ON or MODE Button is pressed to reset
the receiver.The intermittent 4-second beeping will go on for as long as the receiver’s batteries last which
could be in excess of one year.
receiver,indicating that the transmitter is within the normal operating range of 50-feet.Should the receiver NOT
receive a transmitter signal every 2 minutes,the IC software,in the RECEIVER,will begin a 2-HOUR(120-
minute)countdown timing function.If during this 2-hour period,the receiver does not receive a signal from the
transmitter,the receiver will shut down the appliance being controlled by the receiver.The RECEIVER will then
emit a series of rapid”beeps”for a period of 10 seconds.Then after 10 seconds of rapid beeping,the RECEIVER
will continue to emit a single:”beep”every 4 seconds until a transmitter ON or MODE Button is pressed to reset
the receiver.The intermittent 4-second beeping will go on for as long as the receiver’s batteries last which
could be in excess of one year.
To”reset”the RECEIVER and operate the appliance,you must press the ON or MODE button on the
transmitter.By turning the system to ON,the COMMUNICATION-SAFETY operation is overridden and the
system will return to normal operation depending on the MODE selected at the transmitter.The
COMMUNICATION-SAFETY feature will reactivate should the transmitter be taken out of the normal operating
range or should the transmitter’s batteries fail or be removed.
transmitter.By turning the system to ON,the COMMUNICATION-SAFETY operation is overridden and the
system will return to normal operation depending on the MODE selected at the transmitter.The
COMMUNICATION-SAFETY feature will reactivate should the transmitter be taken out of the normal operating
range or should the transmitter’s batteries fail or be removed.