ICOM 236803 Manual De Usuario
4
12
OPERATION
■ Turning power ON
q Push [POWER] to turn power ON.
w If the repeater is programmed for a power on pass-
w If the repeater is programmed for a power on pass-
word by an Icom Dealer, input digit codes directly.
• The keys in the table below can be used for password
input.
• The repeater detects numbers in the same block as
identical. Therefore “01234” and “56789” are the same.
e When the “PASSWORD” indication does not clear
after inputting 4 digits, the input code number may
be incorrect. Turn power off and start over in this
case.
be incorrect. Turn power off and start over in this
case.
■Receiving and transmitting
D Receiving
q Push [POWER] to turn power ON.
w Set the audio and squelch levels.
w Set the audio and squelch levels.
➥Rotate [SQUELCH] fully counterclockwise in ad-
vance.
➥Rotate [VOLUME] to adjust the audio output level.
➥Rotate [SQUELCH] clockwise until the noise dis-
appears.
e Push [UP] or [DN] to select the desired channel.
• When receiving a signal, BUSY indicator turns ON and
audio is emitted from the speaker.
• Further adjustment of [VOLUME] to a comfortable listen-
ing level may be necessary at this point.
D Transmitting
q Take the microphone off hook.
w Wait for the channel to become clear.
e Push and hold [PTT] to transmit, then speak into the
w Wait for the channel to become clear.
e Push and hold [PTT] to transmit, then speak into the
microphone at your normal voice level.
r Release [PTT] to receive.
IMPORTANT:
To maximize the readability of the transmitted signal:
(1) Pause briefly after pushing [PTT].
(2) Hold the microphone 1 to 2 inch (2.5 to 5 cm) from
To maximize the readability of the transmitted signal:
(1) Pause briefly after pushing [PTT].
(2) Hold the microphone 1 to 2 inch (2.5 to 5 cm) from
your mouth, then speak into the microphone at a
normal voice level.
normal voice level.
■Set mode
D Entering the set mode
q Push [POWER] to turn power OFF, if repeater
power is ON.
w While pushing [PROG], [ANI CLR] and [DN], turn
power ON.
e After repeater emits beep “Pi,” release [PROG],
[ANI CLR] and [DN], then push [PROG] again.
r After repeater emits beep “Pi Pi,” release [PROG] to
enter the set mode.
D Return to the normal operating mode
q Push [POWER] to turn power OFF, if repeater
power is ON.
w Then turn power ON to return to the normal operat-
ing mode.
D Set mode contents
• S01 LW RPTSQL : Noise squelch threshold level
on the repeater operation
• S02 LW POWER
: Transmit Low power setting
• S03 HW POWER
: Transmit High power setting
• S04 LN AFDEV
: AF deviation for narrow band-
width
• S05 LW AFDEV
: AF deviation for wide bandwidth
• S06 LN TONEDEV : Continuous tone deviation for
narrow bandwidth
• S07 LW TONEDEV: Continuous tone deviation for
wide bandwidth
• S08 LN ETONE
: External tone deviation for nar-
row bandwidth
• S09 LW ETONE
: External tone deviation for wide
bandwidth
• S10 LN RPTAF
: AF deviation for narrow band-
width on the repeater operation
• S11 LW RPTAF
: AF deviation for wide bandwidth
on the repeater operation
L: Low power, H: High power,
W: Wide bandwidth, N: Narrow bandwidth
W: Wide bandwidth, N: Narrow bandwidth
KEY
[DN]
[UP]
[MONI] [RPT/BASE] [REMOTE]
NUMBER
0
1
2
3
4
5
6
7
8
9