G-Light Technology Co. Ltd. RHGGOKIT Manual De Usuario

1.  Be sure the Garage Door is in sight and all vehicles and any persons are away from the garage door during the 

     installation of the Transmitter.

2.  Determine which headlamp has more working room behind it. The Transmitter can be installed on either headlamp.

3.  Operate your high beam switch and observe which lights are the actual high beams. You will tap the two wires of 

      the Transmitter to the two wires that power the high beam.

4.  If your high beam connector has more than 2 wires, refer to the diagram below to see if your headlight 

     connector/bulb code matches the below. Your highbeam bulb will have one of the numbers stamped on it. 

     If your high beam only has 2-wires, go on to step-5.

IMPORTANT: Only operate the garage door when it is in sight to prevent injury to people or property.

The door will activate a second after receiving the signal. 

If you are still unable to activate the door, see our troubleshooting section on our website (www.rinkuhaus.com).

Operating range is up to 100ft (30meters) depending on vehicle and other physical obstructions.

Red wire from the Transmitter

End Cap of the Posi-Tap with 

transmitter wires

Headlight Power wire to be tapped

The body of the Posi-Tap to lock

the wire in place

5.  Once you have found the high beam wires, use the supplied Posi-Taps to connect to these two wires. 

      Tap Red wire from TX to the Highbeam Power wire. Tap Black wire from TX to the Highbeam Ground wire.

      See diagram below on how to correctly secure the wire Posi-tap connectors.

     When the Transmitter is activated, the LED will light up RED. The door will open or close.     

7.  Secure the Transmitter and all wiring away from any moving parts of your vehicle using plastic ties and the adhesive. 

      If you have a sealed back cover type headlamp, mount the Transmitter inside the headlamp and close the back cover.

You can expand your Rinkuhaus world to multiple vehicles or doors. Additional Receivers and Transmitters are 

available for purchase on our website (www.rinkuhaus.com). 

The Rinkuhaus In-Car Transmitter can control up to 5 Receivers. This means that the one transmitter in your vehicle 

Many homes have multiple garage doors or a property gate. Just add an additional receiver to those doors and 

control them with the one transmitter already in your car. 

Here is one possible example if you had multiple Rinkuhaus Receivers set up in your home:

For instance you have a vacation home or parents’ home and you add a Rinkuhaus Receiver to their garage door, you 

golf carts, etc.) that use a gate on your property, you can install a Transmitter on each of them and they can operate 

the same door or gate that has the one Receiver already installed. Make life more convenient for your entire household 

or business by adding a Transmitter to those vehicles!

NEED MORE HELP?    Visit www.RINKUHAUS.com for more resources and helpful hints!

RED wire :    Connect to Headlight Highbeam signal wire

 

power +12V

BLACK wire:  Connect to Headlight Highbeam Ground

LED

Red Wire

Black wire

Black Color

Unit

>>> If you have just purchased this kit, no programming is necessary <<< 

NOTE: The Transmitter(TX) is pre-programmed to the Receiver (RX) module in each kit f

e.  

(1).  To enter programming mode, press and hold the button of the Receiver for 5 seconds. T

RANGE.

(2).  Trigger headlights desired number of times to register into RX within 60 seconds of entering programming mode. 

        Example: F

to progr

e. 

        Note: If progr

conds of entering programming mode or if RX is pressed/released again, it will return 

                   to standby and the LED will be GREEN.

(3). Once the RX has received the signal from the TX, the LED on the R

 YELLOW. The LED will turn GREEN to c

rm programming. 

(4). Every Receiver can accept up to 20 TX codes. The 21st register will replace the 1st registered. The 22nd will replace the 2nd registered, etc.       

(5). Every Transmitter can tr

erent codes b

t

●

 To Erase ALL memory from the Receiver (RX):

(1).  Disconnect power to the Receiver(RX) and reconnect.   

(2).  Dur

conds of power connection, press and hold the RX’s program button for 20 seconds, then LED will quick

D. 

(3).  Release the programmer button. LED will con

s. 

(4).  When all memory has been erased, the LED will light GREEN and return to Standby mode.
●

 To delete a SINGLE memory from the Receiver (RX):

(1).  Enter programming mode by pressing and holding the button of the RX for 5 seconds

RANGE. 

(2).  Trigger headlights desired number of times of the register you want to erase within 60 seconds of entering programming mode. 

        Example: F

to erase what was progr

e. 

        Note: If progr

conds of entering programming mode or if RX is pressed/released again, it will return 

                   to standby and the LED will be GREEN.   

(3). Once the RX has received the signal from the TX,  LED on the R

D. The LED will then turn GREEN to c

rm the erase.

PAGE 2 of 2

Transmitter (TX)

This device complies with part 15 of the FCC Rules. 

Operation is subject to the following two conditions: 

(1) this device may not cause harmful interference and 

(2) this device must accept any interference received, including interference that may cause undesired operation.