GUGLIELMI SNC DI GUGLIELMI GUGLIELMO E C. AK2 Manual De Usuario
HAWK2_01MI
web: www.guglielmisnc.it
Via Cagliari, 19 - Tel. +390112482361 web: www.guglielmisnc.it Via Cagliari, 19 - Tel. +390112482361
e-mail: info@guglielmisnc.it
10153 Torino - ITALY e-mail: info@guglielmisnc.it
10153 Torino - ITALY
HAWK 2
SETTING FOR OPERATION
The HAWK 2 movement detector can be configured in mono direction mode (one direction only) or
in bi directional mode (in both directions).
Remove the rubber plug from the lower section of the detector (Fig. 1-A) and set the required
function through the dip-switch (Fig. 1-B), choosing from the possibilities indicated in the table:
The HAWK 2 movement detector can be configured in mono direction mode (one direction only) or
in bi directional mode (in both directions).
Remove the rubber plug from the lower section of the detector (Fig. 1-A) and set the required
function through the dip-switch (Fig. 1-B), choosing from the possibilities indicated in the table:
DSW1 DSW2 DSW4 SENSITIVITY CONDITION
OFF
-
ON
Low
Movement is detected in both directions
OFF
-
OFF
High
Movement is detected in both directions
ON
OFF
ON
Low
Approach to the sensor is detected
ON
OFF
OFF
High
Approach to the sensor is detected
ON
ON
ON
Low
Movement away from the sensor is detected
ON
ON
OFF
High
Movement away from the sensor is detected
ASSEMBLY AND ORIENTATION
HAWK 2 can be installed at the centre of the door to be controlled or on the side, on non-vibrating
structures (walls or ceiling) and at a maximum height of 6 m. Use the template supplied to prepare
the holes.
Fasten the device using the prepared holes, remove the lower cover (Fig. 2-A) and loosen the screw
that blocks the detector orientation. Direct the detector toward the area to be controlled and lock in
that position.
For correct operation, do not install HAWK 2 :
HAWK 2 can be installed at the centre of the door to be controlled or on the side, on non-vibrating
structures (walls or ceiling) and at a maximum height of 6 m. Use the template supplied to prepare
the holes.
Fasten the device using the prepared holes, remove the lower cover (Fig. 2-A) and loosen the screw
that blocks the detector orientation. Direct the detector toward the area to be controlled and lock in
that position.
For correct operation, do not install HAWK 2 :
- facing the moving parts of the door
- facing fluorescent lights (minimum distance 2m)
- facing areas where rain could provoke water fluxes
These conditions could activate the device and cause the unwanted opening of the door.
ELECTRICAL CONNECTIONS
Connect the pre-wired cable as indicated in table 1 then power the detector.
HAWK 2
The LED on the detector front panel (Fig. 2-B) will indicate the detection of a movement, for all the
time the relay is excited.
time the relay is excited.
A
E
F B
B A
Fig.1
Fig.2
Tab.1
RELAY CONTACT SETTING
HAWK 2 has a relay with switching contact.
According to the setting of the dip-switch 3 (Fig. 1-B) in the lower section of the detector, the
combinations described in table 2 can be obtained.
These conditions are valid when the device is powered.
HAWK 2 has a relay with switching contact.
According to the setting of the dip-switch 3 (Fig. 1-B) in the lower section of the detector, the
combinations described in table 2 can be obtained.
These conditions are valid when the device is powered.
Wire colour
Description
Red
12-24 V
AC/DC
Black
12-24 V
AC/DC
Green
COM relay contact
Brown
NO contact (when device is not powered)
Blue
NC contact (when device is not powered)