Beat-Sonic Co. Ltd S27870000 Manual De Usuario

Descargar
Página de 2
CHIME-NETIC 
User Manual
Dynamo Button
Wireless Chime
Before Installing
System Expansion Options
Installation Instructions
1.Important
a) The Dynamo Button Transmitter is fully water submersible
  however the Wireless Receiver is not. Please do not get the
  receiver unit wet. 
b) Do not disassemble, repair or modify.
c) Always use the recommended power supply.
2.Attention
3.Pack Contents
Dynamo Button Transmitter x 1
Wireless Receiver x 1
Power Adapter x 1
User Manual x 1 
Call Label Sheet x 1
B.Suspend the Dynamo Button Transmitter using
  
hook or lanyard
A. Installing Dynamo Button Transmitter using
  double-sided tape
2.Melody Selection
1. Two Buttons & One Receiver
a) Avoid installing the Dynamo Button Transmitter on or directly 
near metal surfaces as this will reduce the operating range. 
b) When locating the Dynamo Button Transmitter onto a vinyl 
coated door or door frame, always check the operating 
performance before final installation as the internal metal 
frame may affect perfomance.  
Program an extra Dynamo Button Transmitter to operate with the 
Wireless Receiver. Extra Dynamo Button Transmitter (product code: 
CNB2US-1) required.
2. One Button & Two Receivers
Program an extra Wireless Receiver to operate with the Dynamo 
Button Transmitter. Extra Wireless Receiver (product code: 
CNB2US-2) required.
3. Three Buttons & One Receiver
Program an extra two Dynamo Button Transmitter to operate with the 
Wireless Receiver. Up to a total of three (3) Dynamo Button 
Transmitters can be programmed to each Wireless Receiver.Two 
extra Dynamo Button Transmitters (Product code: CNB2US-1) 
required.
4. One Button & Three or More Receivers
Program an extra two or more Wireless Receivers to operate with 
each Dynamo Button Transmitter. An unlimited number of Wireless 
Receivers can be programmed to operate with each Dynamo Button 
Transmitter. Two or more extra Wireless Receivers (product code: 
CNB2US-2) required.
5. Two Buttons & Two Receivers
Program an extra Dynamo Button Transmitter and an extra Wireless 
Receiver. One extra Dynamo Button Transmitter (product code: 
CNB2US-1) and one extra Wireless Receiver (product code: 
CNB2US-2) required. 
6. Three Buttons & Multiple Receivers 
Program up to three Dynamo Button Transmitters per Wireless 
Receiver. An unlimited number of Wireless Receivers can be 
programmed to operate with each Dynamo Button Transmitter. Extra 
Dynamo Button Transmitters (product code: CNB2US-1) and extra 
Wireless Receivers (product code: CNB2US-2) required. 
1. Connect the Wireless Receiver to a power outlet 
using the approved AC power adapter.
2. Press the Dynamo Button Transmitter to confirm the 
chime is now operational.
3. Select the desired mounting position for the 
Dynamo Button Transmitter making sure it is within 
range of the Wireless Receiver. Note that walls and 
doors will reduce the effective range. 
4. Be sure to avoid mounting the Dynamo Button 
Transmitter on metal surfaces as this will greatly 
reduce its effective range.
5. Confirm that the chime operates reliably for the 
chosen positions then secure using either the 
double sided tape or by using a wall hook or screw. 
Operating Instructions
1.Normal Operation
The Wireless Receiver and Dynamo Button Transmitter have 
been pre-programmed from factory and are ready to use. Simply 
install according to the above instructions and the Wireless 
Receiver will sound and the indicator light will flash when the 
button is pressed. 
Peel back one side of the 
double-sided tape and attach to the 
back of the Dynamo Button 
Transmitter.
Check that the surface is clean, dry 
and free of any loose material. 
Attach the Dynamo Button 
Transmitter to the desired position 
then press and hold against the 
surface for at least 30 seconds. 
Insert a self tapping screw or a wall 
hook into the marked location. 
For personal use, the Dynamo 
Button Transmitter can be worn 
around the neck using a lanyard 
(lanyard not included). 
* When using for personal use, 
always test first the maximum 
operating range. 
The Dynamo Button Wireless Chime comes 
with 25 selectable ring tones. Press the round 
button on the Wireless Receiver to cycle 
through and select your choice of melody. 
Disconnecting then re-connecting power to 
the unit will reset the melody to the default 
"Ding-Dong" melody. 
3. Volume Control
Press the round button twice quicky to 
adjust the chime volume. The Wireless 
Receiver has three selectable volume 
settings (low, medium, high).
Even greater volume can be achieved by mounting the 
Wireless Receiver against a hard surface to reflect the 
sound. 
Press once to
select melody
Press twice
to adjust
volume
230*326
Please contact Beat-Sonic USA to purchase extra Dynamo Button Transmitters and Wireless Receivers
web: www.beatsonicusa.com              email: info@beatsonicusa.com
472-5, Koushin, Fujieda, Nisshin, Aichi, JAPAN.
TEL: +81-561-73-9000   FAX: +81-561-74-5554
www.beatsonic.co.jp    E-mail: enquiries@beatsonic.co.jp
International inquiries.
USA and Canada inquiries.
14778 Beach Blvd. La Mirada, CA 90638
TEL: 1-714-994-1085  FAX: 1-714-249-4741
www.beatsonicusa.com  E-mail: info@beatsonicusa.com
株式会社 ビートソニック
Beat-Sonic USA Inc.