Transition Networks C4TEF1029-110 Prospecto
Ordering Info
C4TEF1011-110
1300 nm multimode (ST)
[2 km/1.2 mi.] Link Budget: 11.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100 m]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1013-110
1300 nm multimode (SC)
[2 km/1.2 mi.] Link Budget: 11.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100 m]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1014-110
1310 nm single mode (SC)
[20k m/12.4 mi.] Link Budget: 16.0 dB
to
(4) RJ-48
[1.5 km / 0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100 m]
plus 6-pin DIN
[3 m / 10 ft.]
C4TEF1015-110
1310 nm single mode (SC)
[40 k m/24.9 mi.] Link Budget: 26.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100 m]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1016-110
1310 nm single mode (SC)
[60 km/37.3 mi.] Link Budget: 29.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100 m]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1017-110
1550 nm single mode (SC)
[80 km/49.7 mi.] Link Budget: 29.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100 m]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1035-110
1550 nm single mode (SC)
[120 k m/74.6 mi.] Link Budget: 36.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100 m]
plus 6-pin DIN
[3 m/ 10 ft.]
Single Fiber Products
Recommended use in pairs
Recommended use in pairs
C4TEF1029-110
1310 nm TX/1550 nm RX single fiber SM
(SC)
(SC)
[20 km/12.4 mi.] LB: 19.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100 m]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1029-111
1550 nm TX/1310 nm RX single fiber SM
(SC)
(SC)
[20 km/12.4 mi.] LB: 19.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100 m]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1029-112
1310 nm TX/1550 nm RX single fiber SM
(SC)
(SC)
[40 km/24.9 mi.] LB: 25.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100 m]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1029-113
1550 nm TX/1310 nm RX single fiber SM
(SC)
(SC)
[40 km/24.9 mi.] LB: 25.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100 m]
plus 6-pin DIN
[3 m/ 10 ft.]
*Note: RS-232 cable included with each card
(6-pin DIN to DB-9)
(6-pin DIN to DB-9)
Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com
fax: 952.941.2322
info@transition.com
http://www.transition.com
©2010 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
AUTO NEG
AUTO CROSS LINK PASS THRU
TRANSPARENT
RAAN AREEN
NS
NT
LINK RESTORE
AUTO
PAUSE
REMOTE MGMT
LOOP BACK
UPGRADE
REMOTE FIRMWARE
Specifications
Standards
IEEE Std. 802.3 2003; Telecordia TR-NWT-001089: FCC Part 68, UL1459; ITU-
T, ANSI, AT&T, ETSI; TBR 12; PD 7024: 1994 (NTR 4); AMI/B8ZS/HD83; G.703
T, ANSI, AT&T, ETSI; TBR 12; PD 7024: 1994 (NTR 4); AMI/B8ZS/HD83; G.703
Switches
Numerous switch settings for line coding, line buildout, loopback
(per port), AIS setting, data/mgmt RS-232
RS-232 port speed and parity Ethernet port settings: Auto-Negotiation,
Force speed/duplex and enable Transparent Link Pass Through
(per port), AIS setting, data/mgmt RS-232
RS-232 port speed and parity Ethernet port settings: Auto-Negotiation,
Force speed/duplex and enable Transparent Link Pass Through
Jumper
Hardware: mode is determined by DIP switch settings
Software: mode is controlled by the most recently saved,
on-board microprocessor setting
Software: mode is controlled by the most recently saved,
on-board microprocessor setting
Dimensions
Width: 1.72" [44 mm]
Depth: 5.0" [127 mm]
Height: 3.4" [86 mm]
Depth: 5.0" [127 mm]
Height: 3.4" [86 mm]
Power Consumption
6.0 Watts
Environment
See chassis specifications
Shipping Weight
1 lb. [0.45 kg]
Regulatory Compliance
FCC Class A; VCCI Class A; EN 55022 (CISPR 22) Class A; ICES-003
Warranty
Lifetime
Application
C4TEF10xx-11x
point system™ slide-in-module network interface device
Features
Auto-Negotiation for 10/100BASE-TX
AutoCross™ (auto MDI/MDI-X)
Transparent Link Pass Through for
Ethernet
Automatic Link Restoration
Pause (Flow Control)
Remote Management
Local and Remote Loopback
Remote Fiber Loss Signaling
AIS/TAOS
LEDs for each data port
DIP switches for line code, line length,
local loopback or remote loopback
T1/E1/J1 mode settings
Dry Relay Contacts on each TDM port
Local (AUX) Management Interface
(RS232 connector)
Switch selection for Data or
Management mode on RS232
interface
interface
Access to complete status information
on local and remote device
Access to local and remote
configuration
Switch or SNMP selected Baud
rate operation
Remote Firmware Upgrade
4x T1/E1/J1 + 10/100 Ethernet
Copper to Fiber Transport Mux
see also:
Stand-Alone NID
4x T1/E1/J1 + 10/100 Ethernet Transport Mux
Management Features
Report local device status:
• Fiber Link Status
• Copper Link Status for each T1/E1
• Hardware switch settings: LBO, AIS
• Copper Link Status for each T1/E1
• Hardware switch settings: LBO, AIS
on C/F, HW/SW, speed
• AIS detected Fiber & Copper
• Model Number
• Copper & Fiber Connectors
• Model Number
• Copper & Fiber Connectors
Local command operations include:
• Loopback Fiber & T1/E1 per channel
• AIS TX on fiber on loss of copper
• AIS TX on fiber on loss of copper
link & AIS TX on copper on loss of
fiber link
fiber link
• Serial connection speed and parity
(Software Mode)
• T1/E1 Mirror Port Modes
• Boot-load firmware upgrades
• Ethernet settings:
• Boot-load firmware upgrades
• Ethernet settings:
• Auto-Negotiation Enable/Disable
• Force speeds and modes on
• Force speeds and modes on
10/100TX
Remote device status:
• Fiber Link status
• Copper Link status for each T1/E1
• Hardware switch settings: LBO, AIS
• Copper Link status for each T1/E1
• Hardware switch settings: LBO, AIS
on C/F, HW/SW, speed
• AIS detected Fiber & Copper
• Model Number
• Copper & Fiber Connectors
• Model Number
• Copper & Fiber Connectors
Remote Commands:
• Loopback Fiber & T1/E1 per channel
• Serial connection speed and parity
• Serial connection speed and parity
(Software Mode)
• AIS TX on fiber on loss of copper
link & AIS TX on copper on loss of
fiber link
fiber link
• T1/E1 Monitor Modes
• Ethernet settings (Software Mode)
• Force speeds and modes on
• Ethernet settings (Software Mode)
• Force speeds and modes on
10/100TX
• Enable/Disable: Auto-Negotiation;
Link Pass Through; Flow Control;
& AutoCross™
& AutoCross™
Low cost transport capability: (4) T1/E1/J1; (1) Ethernet
and (1) RS232 data channel line.
Target applications include: FTTx, such as Fiber-to-the-
Business, Fiber-to-the-Building, Fiber-to-the-MDU,
Fiber-to-the-Home and Cell tower backhaul.
Fiber-to-the-Home and Cell tower backhaul.
Copper connections compatible with G.703,
AMI/B8ZS/HDB3, 10/100BASE-TX, and RS232 channel;
AMI/B8ZS/HDB3, 10/100BASE-TX, and RS232 channel;
while the optical connection runs at 155Mbps.
TDM traffic is not mapped to Ethernet. A hardware-
based solution guarantees the constant bit rate of TDM
transport without requiring traffic management.
Provides physical layer status monitoring and alarm
classification functions for Telecom operators to
manage their fiber optic network and reduce
transport without requiring traffic management.
Provides physical layer status monitoring and alarm
classification functions for Telecom operators to
manage their fiber optic network and reduce
operation and maintenance costs.
*Note: C4TEF cards cannot be used with the 1-Slot Point System™ Chassis (see page 30). Devices
must be used in pairs. Typical installation will include a chassis card installed in the Point System™
locally and a stand-alone device (S4TEF) installed at the remote location.
must be used in pairs. Typical installation will include a chassis card installed in the Point System™
locally and a stand-alone device (S4TEF) installed at the remote location.
SINGLE
FIBER