Byrne Electrical Specialists Inc. SA04850 Manual De Usuario
User Manual - FCC Deliverables
Page 2 of 6
by: C. Klem
7.0 Show compliance with Section 8.4 of RSS-GEN
The statement should be on label on end product, or if it will not be able to be seen by the end user, then it must
appear in the user manual.
appear in the user manual.
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
8.0 Labelling
8.1 Show compliance with the FCC §15.212(a)(1)(vi)(A) requirement. If the FCC identification number
is not visible when the module is installed inside another device, then the outside of the device into which
the module is installed must also display a label referring to the enclosed module. This exterior label can use
wording such as the following: “Contains Transmitter Module FCC ID: 2AJX5-SA04850 or Contains FCC ID:
2AJX5-SA04850.”
8.2 Show compliance with ISED RP-100 Issue 11, Section 3.2. If the ISED identification number is not
visible when the module is installed inside another device, then the outside of the device into which the
module is installed must also display a label referring to the enclosed module. This exterior label can use
wording such as the following: “Contains Transmitter Module ISED ID: 22009-SA04850 or Contains ISED
ID: 22009-SA04850”
8.3 The modular transmitter is equipped with a permanently affixed label at the time of manufacture. See
image for label location.
is not visible when the module is installed inside another device, then the outside of the device into which
the module is installed must also display a label referring to the enclosed module. This exterior label can use
wording such as the following: “Contains Transmitter Module FCC ID: 2AJX5-SA04850 or Contains FCC ID:
2AJX5-SA04850.”
8.2 Show compliance with ISED RP-100 Issue 11, Section 3.2. If the ISED identification number is not
visible when the module is installed inside another device, then the outside of the device into which the
module is installed must also display a label referring to the enclosed module. This exterior label can use
wording such as the following: “Contains Transmitter Module ISED ID: 22009-SA04850 or Contains ISED
ID: 22009-SA04850”
8.3 The modular transmitter is equipped with a permanently affixed label at the time of manufacture. See
image for label location.
Bottom View
Qi Module (5W)
SA04850
FCC ID: 2AJX5-SA04850
IC ID: 22009-SA04850
IC ID: 22009-SA04850
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
this device must accept any interference received,
including interference that may cause undesired