Transition Networks C4TEF1015-100 Prospecto
Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com
fax: 952.941.2322
info@transition.com
http://www.transition.com
©2009 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
LINK RESTORE
AUTO
REMOTE MGMT
LOOP BACK
UPGRADE
REMOTE FIRMWARE
Low cost transport capability:
(4) T1/E1/J1 and (1) RS232 data channel line
Target applications of the device include:
FTTx, such as Fiber-to-the-Business,
Fiber-to-the-Building, Fiber-to-the-MDU and
Fiber-to-the-Home; Cell Tower backhaul
Fiber-to-the-Building, Fiber-to-the-MDU and
Fiber-to-the-Home; Cell Tower backhaul
Specifications
(see pages 211-222 for complete fiber optic connector specs)
Standards
AMI/B8ZS/HDB3; G.703
Telecordia TR-NWT-001089: FCC Part 68, UL1459; ITU-T,
ANSI, AT&T, ETSI; TBR 12; PD 7024: 1994 (NTR 4)
Telecordia TR-NWT-001089: FCC Part 68, UL1459; ITU-T,
ANSI, AT&T, ETSI; TBR 12; PD 7024: 1994 (NTR 4)
Switches
Numerous switch settings for line coding, line buildout,
loopback (per port), AIS setting, data/mgmt RS-232 and
RS-232 port speed and parity
loopback (per port), AIS setting, data/mgmt RS-232 and
RS-232 port speed and parity
Jumper
Hardware: device mode is determined by DIP switch settings
Software: device mode is controlled by the most recently saved,
on-board microprocessor settings
Software: device mode is controlled by the most recently saved,
on-board microprocessor settings
Dimensions
Width: 1.72" [44 mm]
Depth: 5.0" [127 mm]
Height: 3.4" [86 mm]
Depth: 5.0" [127 mm]
Height: 3.4" [86 mm]
Power Consumption
6.0 Watts
Environment
See chassis specifications
Shipping Weight
1 lb. [0.45 kg]
Regulatory Compliance
FCC Class A; VCCI Class A;
EN 55022 (CISPR 22) Class A; ICES-003
EN 55022 (CISPR 22) Class A; ICES-003
Warranty
Lifetime
Ordering Info
C4TEF1011-100
1300 nm multimode (ST)
[2 km/1.2 mi.] Link Budget: 11.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1013-100
1300 nm multimode (SC)
[2k m/1.2 mi.] Link Budget: 11.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1014-100
1310 nm single mode (SC)
[20 km/12.4 mi.]
Link Budget: 16.0 dB
Link Budget: 16.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1015-100
1310 nm single mode (SC)
[40 km/24.9 mi.]
Link Budget: 26.0 dB
Link Budget: 26.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1016-100
1310 nm single mode (SC)
[60 km/37.3 mi.]
Link Budget: 29.0 dB
Link Budget: 29.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1017-100
1550 nm single mode (SC)
[80 km/49.7 mi.]
Link Budget: 29.0 dB
Link Budget: 29.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1035-100
1550 nm single mode (SC)
[120 km/74.6 mi.]
Link Budget: 36.0 dB
Link Budget: 36.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 6-pin DIN
[3 m/ 10 ft.]
Single Fiber Products
Recommended use in pairs (see page 18)
Recommended use in pairs (see page 18)
C4TEF1029-100
1310 nm TX/1550 nm RX single fiber
single mode (SC)
single mode (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1029-101
1550 nm TX / 1310 nm RX single fiber
single mode (SC)
single mode (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1029-102
1310 nm TX / 1550 nm RX single fiber
single mode (SC)
single mode (SC)
[40 km/24.9 mi.] Link Budget: 25.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 6-pin DIN
[3 m/ 10 ft.]
C4TEF1029-103
1550 nm TX / 1310 nm RX single fiber
single mode (SC)
single mode (SC)
[40 km/ 24.9 mi.] Link Budget: 25.0 dB
to
(4) RJ-48
[1.5 km/ 0.9 mi.]
plus 6-pin DIN
[3 m/ 10 ft.]
*Note: RS-232 cable included with each card
(6-pin DIN to DB-9)
(6-pin DIN to DB-9)
Application
C4TEF10xx-10x
point system™ slide-in-module network interface device
Features
Automatic Link Restoration
Remote Management
Local and Remote Loopback
AIS/TAOS
LEDs for each data port
DIP switches for line code, line
length, local loopback or remote
loopback
loopback
T1/E1/J1 mode settings
Dry Relay Contacts on each TDM port
Mirror Port (SNMP selectable)
Local (AUX) Management Interface
(RS232 connector)
Switch selection for Data or
Management mode on RS232
Access to complete status
information on local and
remote device
remote device
Access to local and remote
configuration
Switch or SNMP selected Baud
rate operation
Remote Firmware Upgrade
4x T1/E1/J1 Copper to Fiber Transport Mux
T1/E1
see also:
4xT1 Transport Mux Stand-Alone NIDs
4x T1/E1/J1 Copper to Fiber Transport Mux
Management Features
Report local device status:
• Fiber Link Status
• Copper Link Status for each T1/E1
• Hardware switch settings: LBO, AIS
• Copper Link Status for each T1/E1
• Hardware switch settings: LBO, AIS
on C/F, HW/SW, speed
• AIS detected Fiber & Copper
• Model Number
• Copper & Fiber Connectors
• Model Number
• Copper & Fiber Connectors
Local command operations include:
• Loopback Fiber & T1/E1 per channel
• AIS TX on fiber on loss of copper link
• AIS TX on fiber on loss of copper link
& AIS TX on copper on loss of
fiber link
fiber link
• Serial connection speed and parity
(Software Mode)
• T1/E1 Mirror Port Modes
(Port Trapping)
• Boot-load firmware upgrades
Remote device status:
• Fiber Link status
• Copper Link Status for each T1/E1
• Hardware switch settings: LBO, AIS
• Hardware switch settings: LBO, AIS
on C/F, HW/SW, speed
• AIS detected Fiber & Copper
• Model Number
• Copper & Fiber Connectors
• Model Number
• Copper & Fiber Connectors
Remote Commands:
• Loopback Fiber & T1/E1 per channel
• Serial connection speed and parity
• Serial connection speed and parity
(Software Mode)
• AIS TX on fiber on loss of copper link
& AIS TX on copper on loss of
fiber link
fiber link
*Note: C4TEF cards cannot be used with the 1-Slot Point System™ Chassis.
The product provides physical layer status monitoring and alarm classification functions for Telecom
operators to
operators to
manage their fiber optic network and reduce OPEX and maintenance costs.
Copper connections are compatible with G.703 and AMI/B8ZS/HDB3; while the optical connection will
run at 155Mbps. A hardware-based solution guarantees the constant bit rate of TDM transport without
requiring traffic management.
run at 155Mbps. A hardware-based solution guarantees the constant bit rate of TDM transport without
requiring traffic management.
Devices must be used in pairs. Typical installation will include a chassis card installed in the Point Sys-
tem™ locally and a stand-alone device (S4TEF) installed at the remote location.
tem™ locally and a stand-alone device (S4TEF) installed at the remote location.
SINGLE
FIBER