Adtran SFP 3.125Gbps 1200-1620nm 1440882G1 Prospecto
Los códigos de productos
1440882G1
jobAid
D
ESCRIPTION
The Small Form‐Factor Pluggable 3.125 Gigabit Ethernet 40 km
(SFP) is a single mode fiber SFP that plugs into a module
designed to accept SFPs. The SFP provides a dual optical interface
to the 3.125 Gigabit Ethernet physical interface. Installed into an
appropriate module, the SFP provides a 3.125 Gigabit Ethernet
interface to the supporting system.
(SFP) is a single mode fiber SFP that plugs into a module
designed to accept SFPs. The SFP provides a dual optical interface
to the 3.125 Gigabit Ethernet physical interface. Installed into an
appropriate module, the SFP provides a 3.125 Gigabit Ethernet
interface to the supporting system.
This SFP should not be used in applications requiring standard
Gigabit (1000Base) Ethernet services.
Gigabit (1000Base) Ethernet services.
NOTE
To ensure compatibility, refer to the documentation provided
with the host module.
with the host module.
The following features are supported on the SFP:
♦
3.125 Gigabit Ethernet data rate
♦
1310 nm Transmitter
♦
Wavelength: 1200 ‐ 1620 nm
♦
Optical distance: 40 km maximum
CAUTION
!
Due to compliance certification requirements, use only SFPs
supplied by ADTRAN with the host module. ADTRAN cannot
certify system integrity with other SFPs.
supplied by ADTRAN with the host module. ADTRAN cannot
certify system integrity with other SFPs.
S
PECIFICATIONS
♦
Optical Specifications:
◊
Optical transmit level: –2 dBm to +3 dBm
◊
Receive power: –27 dBm to –9 dBm
◊
Optical connectors: LC
◊
SFP 8472 Diagnostic compliant
Small Form-Factor Pluggable 3.125
Gigabit Ethernet 40 km
◊
Compatible with SFP MSA
♦
Extended Environmental Support:
◊
Operational temperature range: –40°C to +65°C
◊
Storage temperature range: –40°C to +85°C
◊
Relative humidity to 95%, noncondensing
I
NSTALLATION
To install the SFP into an appropriate module, complete the
following steps:
following steps:
1. Inspect the SFP. If damaged, file a claim with the carrier and
then contact ADTRAN Customer Support.
CAUTION
!
Do not remove the protective end cap from the SFP until the fiber
optic cable is ready to be connected.
optic cable is ready to be connected.
2. Insert the SFP into the SFP cage on the module. Ensure that
the manufacturer’s label on the SFP is facing upward for
correct installation.
correct installation.
3. Slide the SFP all the way into the receptacle until there is an
audible “click”.
NOTE
The latch on the SFP is used to remove the SFP from the cage on
the circuit card.
the circuit card.
S
AFETY
AND
R
EGULATORY
C
OMPLIANCE
CAUTION
!
♦
Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
♦
The SFP meets or exceeds all the applicable requirements of
NEBS, Telcordia GR‐63‐CORE, GR‐1089‐CORE, and ETSI EN
300368. The SFP is intended for deployment in Central Office
type facilities, EEEs, EECs, and locations where the NEC
applies (for example, Customer Premises). The SFP is to be
installed in ADTRAN products in Restricted Access Locations
only, and installed by trained service personnel.
NEBS, Telcordia GR‐63‐CORE, GR‐1089‐CORE, and ETSI EN
300368. The SFP is intended for deployment in Central Office
type facilities, EEEs, EECs, and locations where the NEC
applies (for example, Customer Premises). The SFP is to be
installed in ADTRAN products in Restricted Access Locations
only, and installed by trained service personnel.
CLEI: VAUIAMJP_ _
Product P/N: 1440882G1
Product P/N: 1440882G1
Issue Date: October 2010
Document P/N: 61440882G1-22B