Toshiba RD-XV47KE Manual De Usuario
101
EN
In
troducti
on
Connecti
o
ns
Bas
ic Setup
P
layback
Ed
iti
iti
n
g
V
CR Fu
ncti
on
s
s
Ot
hers
hers
Fu
nc
ti
nc
ti
on
Set
Set
u
p
Recordi
n
g
One-touch Timer Recording
This feature allows you to set the recording length
simply by pressing [REC I].
simply by pressing [REC I].
1
Turn on the unit and insert a
recordable tape.
recordable tape.
Make sure that the TV input is set on the unit.
2
Press [VCR].
3
Select the recording speed using
[REC MODE].
[REC MODE].
(See page 100.)
4
Select the desired channel to record
using [PROG.
using [PROG.
/
] or
[the Number buttons].
5
Press [REC I] repeatedly until the
desired recording time (15 minutes
to 4 hours) appears on the TV
screen.
desired recording time (15 minutes
to 4 hours) appears on the TV
screen.
One-touch Timer Recording will start.
• When the unit reaches the specified time, it will be
turned off automatically.
• To change the recording length during One-touch
Timer Recording, press [REC I] repeatedly until the
desired length appears.
desired length appears.
• To cancel One-touch Timer Recording within the
specified time, press [STOP
S].
Note
• The remaining recording time will appear on the
front panel display during a One-touch Timer
Recording. Press [DISPLAY] can also see the
remaining recording time on the TV screen.
Recording. Press [DISPLAY] can also see the
remaining recording time on the TV screen.
• You cannot pause a One-touch Timer Recording.
• When VCR recording and the Timer Recording are
• When VCR recording and the Timer Recording are
overlapping, the Timer Recording has its priority.
• The unit will automatically switch to the programmed
channel 15 seconds before the programmed time,
and the VCR recording will be cancelled except
when their recording channel is the same. If their
recording channel is the same, the Timer Recording
will start without cancelling the VCR recording, and
the recording will be made on both VCR and the
HDD / DVD.
and the VCR recording will be cancelled except
when their recording channel is the same. If their
recording channel is the same, the Timer Recording
will start without cancelling the VCR recording, and
the recording will be made on both VCR and the
HDD / DVD.
Search
Index Search
An index mark will be assigned at the beginning of
each recording you make. You may skip to a specific
marked point by following the steps below.
1
Press [VCR].
2
Press [SEARCH] to display the index
search menu.
search menu.
3
Enter the number of recordings you
want to skip using
[the Number buttons] within 30
seconds.
want to skip using
[the Number buttons] within 30
seconds.
4
Press [FWD / SLOW
f] or
[SLOW / REV
r] to start index
search.
If you want to go in the forward direction, press
[FWD / SLOW
[FWD / SLOW
f].
If you want to go in the reverse direction, press
[SLOW / REV
[SLOW / REV
r].
After index search, the VCR will play back the
tape automatically.
tape automatically.
Note
• This function is not available during recording.
Time Search
This feature allows you to go to a specific point on a
tape by entering the exact amount of time you want to
skip in order to reach the point.
1
Press [VCR].
2
Press [SEARCH] repeatedly until the
time search menu appears.
time search menu appears.
3
Enter your desired time to skip using
[the Number buttons] within 30
seconds.
[the Number buttons] within 30
seconds.
4
Press [FWD / SLOW
f] or
[SLOW / REV
r] to start time
search.
If you want to go in the forward direction, press
[FWD / SLOW
[FWD / SLOW
f].
If you want to go in the reverse direction, press
[SLOW / REV
[SLOW / REV
r].
After time search, the unit will play back the tape
automatically.
automatically.
Note
• This function is not available during recording.
• Press [STOP
S] to stop the search.
• If the tape reaches the end during the Search, this
unit will cancel it and rewind the tape.
VCR
VCR
0:15
4:00
3:45
0:30
(Normal Recording)
VCR
VCR
VCR
VCR
E3B90ED_EN.book Page 101 Friday, February 23, 2007 12:38 PM