Toshiba RD-XV48KE Manual De Usuario

84

EN

Before requesting service for this unit, check the table below for a possible cause of the problem you are 
experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore 
proper operation.

Others

The power does not turn on.

• Check that the AC power cord is connected securely.
• Batteries of the remote control are weak.

The unit turns on automatically without any 
operation.

• The unit turns on automatically 2 seconds before the timer recording.

The unit does not function.

• “

” or error message appears if the operation is prohibited.

• Batteries of the remote control are weak or exhausted.

No picture, sound or menu appears on the 
screen.

• Check if the connections are made securely and correctly.
• Check if the cables are damaged.
• Check if a correct external input channel is selected on your TV.

(See page 20.)

• Check if you have completed “Channel” setting. (See pages 22-23.)

“Clock” setting and “Channel” setting cannot 
be performed.

• If a recording is in progress, these operations cannot be performed.

The unit does not operate properly.

• Moisture has condensed inside the unit. Remove the disc and leave the 

unit turned on for about 2 hours until the moisture evaporates.
(See page 3.)

The clock display does not appear on the 
front panel display.

• Check that the AC power cord is connected securely.
• (In case of power failure) Check the breaker and “Clock” setting.

When you forget the password for parental 
lock.

• Please cancel the password and the set level. (See page 74.)

DV signal cannot be input.

• Before connection, turn on the power supplies for both this unit and the 

DVC, and make sure that these units have stopped.

• Only a “DVC-SD” signal can be input from the DVC to this unit. Other 

types of signals are not supported.

• Do not connect any device other than the DVC. Even if a recorder or PC 

with another DV terminal is connected, the DV function will not operate.

• If the DVC is not recognised after connection, turn off the power supply 

for the unit and re-connect the DVC.

The DVC cannot be operated with this unit.

• Signal input or DVC operation from this unit may be disabled depending 

on the type of DVC.

• If a DVC signal cannot be input, use an external input (AV2/AV3) for 

analogue connection via audio/video cables. Use Scart adaptor for 
connecting to AV2.

• DVC control may be disabled depending on the type of DVC, even in a 

mode other than camera mode. In this case, switch to DVD control and 
execute the normal recording procedure while operating the DVC.

Certain functions of the DVC cannot operate.

• Some functions may not operate depending on the type of DVC. For 

example, if the DVC does not support slow playback mode, the slow 
playback function is disabled.

• With DV (AV4), the disc display menu does not appear unless disc 

playback is executed.

DV audio signal cannot be switched.

• For recording with the DVC, the recording audio signal can be set to 12 

bits or 16 bits. However, when 16-bit recording mode is selected, audio 
signal cannot be switched. To record an audio signal, set it to 12 bits.

No image from HDMI connection.

• Check the HDMI connection. (Check the status of the HDMI related 

indications.)

• Check whether the connected monitor device or other device supports 

HDCP. (This unit will not output a video signal unless the other device 
supports HDCP.)

• Check the setting of HDMI.
• Check whether the output format of this unit (HDMI FORMAT) matches 

the supported input format of other connected device.

• If the unit is connected to the unauthorised display device with an HDMI 

cable, the audio and video signals may not be output when playing back 
a commercial DVD-video.

E3LG0ED_EN.book  Page 84  Wednesday, April 30, 2008  11:52 AM