Intel 2020M AW8063801211202 Hoja De Datos
Los códigos de productos
AW8063801211202
Datasheet
19
Electrical Specifications
2.6.2
DC Voltage and Current Specification
Table 5.
Voltage and Current Specifications
Symbol
Parameter
Min
Typ
Max
Unit Notes
1, 2
NOTES:
1.
Unless otherwise noted, all specifications in this table are based on estimates and simulations or empirical data.
These specifications will be updated with characterized data from silicon measurements at a later date.
2.
Adherence to the voltage specifications for the processor are required to ensure reliable processor operation.
VID Range
VID
0.8500
—
1.5
V
3
3.
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and can not be altered. Individual maximum VID values are calibrated during manufacturing such
that two processors at the same frequency may have different settings within the VID range. Note this differs
from the VID employed by the processor during a power management event (Thermal Monitor 2, Enhanced Intel
SpeedStep
®
technology, or Extended HALT State).
V
CC
Processor Number
E2200
E2180
E2160
E2140
E2180
E2160
E2140
V
CC
for
775_VR_CONFIG_06
2.2 GHz
2.0 GHz
1.8 GHz
1.6 GHz
2.0 GHz
1.8 GHz
1.6 GHz
Refer to
and
V
4, 5, 6
4.
These voltages are targets only. A variable voltage source should exist on systems in the event that a different
voltage is required. See
and
for more information.
5.
The voltage specification requirements are measured across VCC_SENSE and VSS_SENSE lands at the socket
with a 100 MHz bandwidth oscilloscope, 1.5 pF maximum probe capacitance, and 1 MΩ minimum impedance. The
maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from the system
is not coupled into the oscilloscope probe.
6.
Refer to
for the minimum, typical, and maximum V
CC
allowed for a given current. The
processor should not be subjected to any V
CC
and I
CC
combination wherein V
CC
exceeds V
CC_MAX
for a given
current.
V
CC_BOOT
Default V
CC
voltage for initial power up
—
1.10
—
V
V
CCPLL
PLL V
CC
- 5%
1.50
+ 5%
I
CC
Processor Number
E2200
E2180
E2160
E2140
E2180
E2160
E2140
V
CC
for
775_VR_CONFIG_06
2.2 GHz
2.0 GHz
1.8 GHz
1.6 GHz
2.0 GHz
1.8 GHz
1.6 GHz
—
—
75
75
75
75
75
75
75
A
7
7.
I
CC_MAX
specification is based on the V
CC_MAX
loadline. Refer to
for details.
V
TT
FSB termination voltage
(DC + AC specifications)
(DC + AC specifications)
1.14
1.20
1.26
V
8
8.
V
TT
must be provided via a separate voltage source and not be connected to V
CC
. This specification is measured
at the land.
VTT_OUT_LEFT and
VTT_OUT_RIGHT
I
VTT_OUT_RIGHT
I
CC
DC Current that may be drawn from
VTT_OUT_LEFT and VTT_OUT_RIGHT per
pin
VTT_OUT_LEFT and VTT_OUT_RIGHT per
pin
—
—
580
mA
9
9.
Baseboard bandwidth is limited to 20 MHz.
I
TT
I
CC
for V
TT
supply before V
CC
stable
I
CC
for V
TT
supply after V
CC
stable
—
—
4.5
4.6
4.6
A
10
10.This is maximum total current drawn from V
TT
plane by only the processor. This specification does not include
the current coming from R
TT
(through the signal line). Refer to the Voltage Regulator-Down (VRD) 11.0 Processor
Power Delivery Design Guidelines For Desktop LGA775 Socket to determine the total I
TT
drawn by the system.
This parameter is based on design characterization and is not tested.
I
CC_VCCPLL
I
CC
for PLL land
—
—
130
mA
I
CC_GTLREF
I
CC
for GTLREF
—
—
200
μA