HP DL380e Gen8 CTO 669256-B21 Manual De Usuario
Los códigos de productos
669256-B21
NOTE: This section lists some of the steps required to configure a Factory Integrated Model. To ensure only valid configurations are
ordered, HP recommends the use of an HP approved configurator. Contact your local sales representative for information on
configurable product offerings and requirements.
NOTE: Factory Integrated Models must start with a CTO Server.
NOTE: FIO indicates that this option is only available as a factory installable option.
NOTE: All Factory Integrated Models will be populated with sufficient hard drive blanks based on the number of initial hard drives
ordered with the server.
ordered, HP recommends the use of an HP approved configurator. Contact your local sales representative for information on
configurable product offerings and requirements.
NOTE: Factory Integrated Models must start with a CTO Server.
NOTE: FIO indicates that this option is only available as a factory installable option.
NOTE: All Factory Integrated Models will be populated with sufficient hard drive blanks based on the number of initial hard drives
ordered with the server.
Step 1: Base Configuration (choose one of the following configurable models)
NOTE: Rail kits and cable management solutions are optional in CTO. See "Step 3: Choose Additional Factory Integratable Options" for
details on ordering.
NOTE: The DL380e ships standard with the Dynamic Smart Array B120i controller which provides support for up to 6 SATA drives
(greater than 4 drives requires additional cable, p/n 675856-B21) and data transmission speeds up to 3Gb/s. Customers requiring SAS
support or greater than 6 drives should select either a Smart Array family controller or the HP Dynamic Smart Array B320i controller
(p/n 661402-B21, implemented via riser).
NOTE: When the SAS-enabled riser board with the Smart Array B320i controller is installed in the server, the embedded Smart Array
B120i controller is automatically disabled. In the absence of another storage controller or an expander backplane, front drives operate
in ACHI or Legacy mode. In these two modes, the drives are not part of a hardware RAID or a member of a logical drive. The Locate,
Drive status, and Do not remove LEDs in the drive carrier are disabled.
NOTE: Number of HDD blanks in a given chassis is same as number of drive cage bays.
NOTE: Power Supply not included - choose from Options section.
details on ordering.
NOTE: The DL380e ships standard with the Dynamic Smart Array B120i controller which provides support for up to 6 SATA drives
(greater than 4 drives requires additional cable, p/n 675856-B21) and data transmission speeds up to 3Gb/s. Customers requiring SAS
support or greater than 6 drives should select either a Smart Array family controller or the HP Dynamic Smart Array B320i controller
(p/n 661402-B21, implemented via riser).
NOTE: When the SAS-enabled riser board with the Smart Array B320i controller is installed in the server, the embedded Smart Array
B120i controller is automatically disabled. In the absence of another storage controller or an expander backplane, front drives operate
in ACHI or Legacy mode. In these two modes, the drives are not part of a hardware RAID or a member of a logical drive. The Locate,
Drive status, and Do not remove LEDs in the drive carrier are disabled.
NOTE: Number of HDD blanks in a given chassis is same as number of drive cage bays.
NOTE: Power Supply not included - choose from Options section.
HP Models
HP ProLiant DL380e Gen8 12 LFF Configure-to-order Server
NOTE: This CTO server is designed for customers who are looking for maximum 2U
storage performance and density. This model requires two (2) Smart Array P420
controllers if using more than 8 drives.
storage performance and density. This model requires two (2) Smart Array P420
controllers if using more than 8 drives.
669254-B21
Factory Integrated Model ships with:
2 x HP Smart Socket Guides for fast processor installation.
12 DIMM slots for RDIMM, LRDIMM and UDIMM Memory installation
HP Ethernet 1Gb 4-port 366i Adapter
HP Dynamic Smart Array B120i Controller with Zero Memory (ZM)
I/O slots - 4 Slots come standard:
12 DIMM slots for RDIMM, LRDIMM and UDIMM Memory installation
HP Ethernet 1Gb 4-port 366i Adapter
HP Dynamic Smart Array B120i Controller with Zero Memory (ZM)
I/O slots - 4 Slots come standard:
Slot 1 - FL/FH x4 PCIe 3.0 (x8 connector)
Slot 2 - HL/FH x8 PCIe 3.0 (x16 connector)
Slot 3 - HL/FH x8 PCIe 3.0 (x8 connector)
Slot 4 - Low Profile x4 PCIe 2.0 (x8 connector)
Additional Slots may be added via selections from the PCI Information and
Slot 2 - HL/FH x8 PCIe 3.0 (x16 connector)
Slot 3 - HL/FH x8 PCIe 3.0 (x8 connector)
Slot 4 - Low Profile x4 PCIe 2.0 (x8 connector)
Additional Slots may be added via selections from the PCI Information and
Options subsection
System Fans - 4 (1 additional fan included with purchase of second processor)
Drive Cage - 12-LFF
USB - 4 Rear, 1 Front, 1 Internal, 1 SD slot
HP iLO Management Engine (standard)
System Fans - 4 (1 additional fan included with purchase of second processor)
Drive Cage - 12-LFF
USB - 4 Rear, 1 Front, 1 Internal, 1 SD slot
HP iLO Management Engine (standard)
NOTE: New options are available for Rack Rail Kits; these options are no longer
standard on-board with this Model Part Number. Please see HP Rack Options below for
optional required options.
standard on-board with this Model Part Number. Please see HP Rack Options below for
optional required options.
HP ProLiant DL380e Gen8 12 LFF Configure-to-order Server
NOTE: This CTO server includes an "expander-based" storage backplane. A single Smart
Array P420 controller is capable of controlling all 12 LFF drives and optional rear drives.
Array P420 controller is capable of controlling all 12 LFF drives and optional rear drives.
669257-B21
QuickSpecs
HP ProLiant DL380e Generation 8 (Gen8)
Configuration Information - Factory Integrated Models
DA - 14328 North America — Version 15 — December 21, 2012
Page 28