LEM Products 777 W777 Manual De Usuario

When using electrical appliances, basic safety precautions should be followed to reduce the risk of
fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using the appliance.
2. Place unit on a firm level surface.
3. To avoid fire or shock hazard, plug the appliance directly into a 120V AC electrical outlet.
4. To protect surfaces from damage, lift, do not push or pull unit.
5. Use extreme caution when operating grinder in the presence of children.

6. Always unplug unit when not in use, when changing parts or cleaning.
7. When unplugging, be sure to pull by the plug and not the cord.
8. To disconnect unit, turn switch to OFF position, then remove plug from outlet.
9. Never use fingers to push meat into grinder head. Always use the meat stomper provided.
10. Thoroughly clean the unit and all parts after each use with hot soapy water.

11. Use appliances only for intended household use as described in this manual. Any other use not
recommended by the manufacturer may cause a malfunction or injury and void warranty. The use of
attachments not recommended or sold by LEM Products may cause hazards and will void warranty.
12. To avoid the risk of fire, do not use extension cords. 
13. Do not attempt to repair or adjust any electrical or mechanical functions on this unit without 
contacting an LEM repair technician Toll Free at 877-536-7763. Doing so will void warranty. 
Servicing should be performed as directed by qualified personnel only.
14. Discontinue use if plug or outlet is hot. It is recommended that the outlet be replaced if plug or
outlet is hot to the touch.

Do not operate unit without meat. Do not overload unit when grinding. When grinder is turned off,
cooling fan will no longer operate. Do not touch housing during cool down period. Housing will take
a few minutes to cool down after unit is turned off. Store unit in a cool dry area.

Your LEM grinder is equipped with a circuit breaker to protect the unit. In the event of a power
disruption, abnormal operation or over heating, the motor will temporarily shut down to prevent
damage. If this should happen, follow the seven steps listed below:

Step 1: Turn On/Off switch to off.
Step 2: Unplug unit.
Step 3: Check inside of grinding unit and remove any obstruction.
Step 4: Wait 1 or 2 minutes, then plug unit into wall outlet again.
Step 5: Push Restart Button and release. (Located on back panel of grinder.)
Step 6: Turn switch on.
Step 7: Resume Operation.

LEM Products • 109 May Drive, Harrison, OH 45030 • PH: 877-536-7763 • www.lemproducts.com

1) First grind the meat with the 10mm plate (#5) for a course grind. For a finer grind, do a second 
grind with the 4.5mm plate (#6).  (Unplug the grinder, remove 10mm plate, install the 4.5 mm 
plate.)

2) Mix seasoning into the meat.

3) Unplug the grinder, remove the grinder knife and plate. Install the stuffing plate (#7) in place of 
the knife and plate. Put stuffing tube (#2, 3, or 4) in front of stuffing plate and secure with the 
retaining ring. 

4) Feed ground meat through the grinder into the stuffing casings.

1) Cut meat into 1” chunks.

2) Mix seasoning into the meat or marinate the meat.

3) Unplug the grinder, install the knife, 4.5 mm plate (#6) and stuffing tube.

4) Feed meat chunks into the grinder.

5) Fine grind directly into the stuffing casings.

1) First grind the meat with the 10mm plate (#5) for a course grind.

2) Mix seasonings into the meat or marinate the meat.

3) Unplug the grinder, remove the 10mm plate. Install the knife, 10 mm plate (#5) and stuffing 
tube.

4) Second grind the meat through this plate directly into the casings.

LEM Products • 109 May Drive, Harrison, OH 45030 • PH: 877-536-7763 • www.lemproducts.com