Conteg RDF-48-80/120 Hoja De Datos
Example of installed plates and
cable opening in a rack
Dimensions of brush
openings:
width 60 - 76x400 mm
width 80 - 76 x600 mm
Brush dimensions:
width 60 - 60x400 mm
width 80 - 60x600 mm
BOTTOM PLATES
Bottom plates are designed as
segmented. Full bottom plate
(set) consists of 3 or 4 plates. They
are delivered either installed or
separately in a carton box. Plate is
always delivered including blank-
ing panels/plastic caps.
Installation in the rack
Installation in the rack
Code *
RHF/
RDF/RSF
footprint in
mm
CO-BI-60/80-XXX-Y
600x800
CO-BI-60/100-XXX-Y 600x1000
CO-BI-60/120-XXXX-Y 600x1200
CO-BI-80/80-XXX-Y
CO-BI-60/120-XXXX-Y 600x1200
CO-BI-80/80-XXX-Y
800x800
CO-BI-80/100-XXX-Y 800x1000
CO-BI-80/120-XXXX-Y 800x1200
CO-BI-80/120-XXXX-Y 800x1200
Code
RHF/RDF/RSF
width in mm
CO-BU-60-X-Y
600
CO-BU-80-X-Y
800
* To be ordered together with rack which you
wish to have the plate installed in
Define the desired bottom plate
set. Choose the design of plates
you like and write its codes (A -
I) in front to rear order instead
of X. Write B for gray (RAL 7035)
or H for black (RAL 9005) instead
of Y. Any plate may be omitted
(incomplete bottom plate sets
applicable - results in no IP pro-
tection). Write 0 if the position
should leave empty.
Delivery in carton box
Delivery in carton box
Single plates can be delivered in
carton boxes. Choose the design
you like and write its code (A - I)
instead of X. Write B for gray (RAL
7035) or H for black (RAL 9005)
instead of Y.
300x100mm
cable entry openings,
covered by removable
sheet steel blank panel
300x50mm
cable entry openings,
covered by removable
sheet steel blank panel
4" (100mm)
cable entry openings,
covered by removable
plastic cap
420x280mm
ventilation unit openings,
covered by removable
sheet steel blank panel,
allow installation of 6-fan
unit
420x440mm
ventilation unit openings,
covered by removable
sheet steel blank panel,
allow installation of 9-fan
unit
RECOMMENDED ACCESSORIES FOR PREMIUM PLATE CABLE ENTRIES
All cable entries are delivered with removable blanking panels or plastic caps. If removed, open cable entries result in no IP
rating so water or dust can enter the rack. Sharp edges and poor management of entering cables can also negatively impact
the service life of cables and their performance in data transmission. With products from the portfolio “cable protection in
cable openings” both problems can be prevented.
Recommended
accessories
Code
DP-KP-LEM
DP-KP-HCE
DP-KP-KAR
DP-KP-KAR4
DP-KP-KAR4-D
DP-KP-HCE
DP-KP-KAR
DP-KP-KAR4
DP-KP-KAR4-D
Recommended
accessories
Code
DP-KP-RB4
These openings are used for installation of ventila-
tion unit. For more information on ventilation units
and related products go to www.conteg.com
A design *
B design
I design
H design
G design
F design
E design
D design
C design
A, B, C, D, E design: lateral plates
Complete bottom plate contains always two
Complete bottom plate contains always two
plates of A, B, C, D or E design. Combination of
two different plates is allowed.
F, G design: central plates for 800 and 1200mm
deep racks
Complete bottom plate contains always one
Complete bottom plate contains always one
(800mm deep racks) or two (1200mm deep racks)
plates of F or G design. Combination of two dif-
ferent plates is allowed.
H, I design: central plates for 1000mm deep
H, I design: central plates for 1000mm deep
racks
Complete bottom cover contains always one
Complete bottom cover contains always one
plate of H or I design.
* plate is designed as divided with double brush
600mm
800mm
N/A
Example
CO-BI-80/80-CFC-X
installed in rack
C (front)
C (rear)
Example
CO-BI-80/100-DIB-X
installed in rack
D (front)
I
B (rear)
Example
CO-BI-80/120-AFFA-X
installed in rack
A (front)
F
A (rear)
F
Example
CO-BU-80-G-X
delivered in carton box
G
F