Conteg RDF-42-80/120 Hoja De Datos

Example of installed plates and

cable opening in a rack

Dimensions of brush

openings:

width 60 - 76x400 mm

width 80 - 76 x600 mm

Brush dimensions:

width 60 - 60x400 mm

width 80 - 60x600 mm

BOTTOM PLATES

Bottom plates are designed as

segmented. Full bottom plate

(set) consists of 3 or 4 plates. They

are delivered either installed or

separately in a carton box. Plate is

always delivered including blank-

ing panels/plastic caps.
Installation in the rack

Code *

RHF/

RDF/RSF

footprint in

CO-BI-60/80-XXX-Y

600x800

CO-BI-60/100-XXX-Y 600x1000
CO-BI-60/120-XXXX-Y 600x1200
CO-BI-80/80-XXX-Y

800x800

CO-BI-80/100-XXX-Y 800x1000
CO-BI-80/120-XXXX-Y 800x1200

Code

RHF/RDF/RSF

width in mm

CO-BU-60-X-Y

600

CO-BU-80-X-Y

800

* To be ordered together with rack which you

wish to have the plate installed in

Define the desired bottom plate

set. Choose the design of plates

you like and write its codes (A -

I) in front to rear order instead

of X. Write B for gray (RAL 7035)

or H for black (RAL 9005) instead

of Y. Any plate may be omitted

(incomplete bottom plate sets

applicable - results in no IP pro-

tection). Write 0 if the position

should leave empty.
Delivery in carton box

Single plates can be delivered in

carton boxes. Choose the design

you like and write its code (A - I)

instead of X. Write B for gray (RAL

7035) or H for black (RAL 9005)

instead of Y.

300x100mm

cable entry openings,

covered by removable

sheet steel blank panel

300x50mm

cable entry openings,

covered by removable

sheet steel blank panel

4" (100mm)

cable entry openings,

covered by removable

plastic cap

420x280mm

ventilation unit openings,

covered by removable

sheet steel blank panel,

allow installation of 6-fan

unit

420x440mm

ventilation unit openings,

covered by removable

sheet steel blank panel,

allow installation of 9-fan

unit

RECOMMENDED ACCESSORIES FOR PREMIUM PLATE CABLE ENTRIES

All cable entries are delivered with removable blanking panels or plastic caps. If removed, open cable entries result in no IP

rating so water or dust can enter the rack. Sharp edges and poor management of entering cables can also negatively impact

the service life of cables and their performance in data transmission. With products from the portfolio “cable protection in

cable openings” both problems can be prevented.

Recommended

accessories

Code

DP-KP-LEM
DP-KP-HCE
DP-KP-KAR
DP-KP-KAR4
DP-KP-KAR4-D

Recommended

accessories

Code

DP-KP-RB4

These openings are used for installation of ventila-

tion unit. For more information on ventilation units

and related products go to www.conteg.com

A design *

B design

I design

H design

G design

F design

E design

D design

C design

A, B, C, D, E design: lateral plates
Complete bottom plate contains always two

plates of A, B, C, D or E design. Combination of

two different plates is allowed.

F, G design: central plates for 800 and 1200mm

deep racks
Complete bottom plate contains always one

(800mm deep racks) or two (1200mm deep racks)

plates of F or G design. Combination of two dif-

ferent plates is allowed.
H, I design: central plates for 1000mm deep

racks
Complete bottom cover contains always one

plate of H or I design.

* plate is designed as divided with double brush

600mm

800mm

N/A

Example

CO-BI-80/80-CFC-X

installed in rack

C (front)

C (rear)

Example

CO-BI-80/100-DIB-X

installed in rack

D (front)

B (rear)

Example

CO-BI-80/120-AFFA-X

installed in rack

A (front)

A (rear)

Example

CO-BU-80-G-X

delivered in carton box