Philips Smart LED TV 40PFL3208T 40PFL3208T/12 Manual De Usuario
Los códigos de productos
40PFL3208T/12
EN 39
En
gl
is
h
Satellite settings
What you can do
This TV can receive signals from 4 different
low noise block-down converters (LNBs).
An LNB is mounted at the end pole of the
dish antenna and captures signals from a
satellite.
Note:
low noise block-down converters (LNBs).
An LNB is mounted at the end pole of the
dish antenna and captures signals from a
satellite.
Note:
Satellite reception is available for certain
models only. [Search for satellite] is
only available if the TV supports DVB-S.
only available if the TV supports DVB-S.
To receive satellite channels, connect a
satellite receiver to the SAT connector
on your TV.
satellite receiver to the SAT connector
on your TV.
Install satellite channels
Reinstall satellites
1. While you watch TV, press .
1. While you watch TV, press .
2. Select [Setup] > [Search for satellite] >
[Reinstall satellites].
3. Follow the onscreen instructions to
complete the installation.
[Reinstall satellites].
3. Follow the onscreen instructions to
complete the installation.
4. Once complete, select [Finish], then press
OK.
OK.
Select connection type
When you install satellite channels, you need
to set the connection type. The number of
LNBs on your dish antenna determines the
number of satellite channels you can install.
1. While you reinstall satellites, select
When you install satellite channels, you need
to set the connection type. The number of
LNBs on your dish antenna determines the
number of satellite channels you can install.
1. While you reinstall satellites, select
[Settings], then press OK.
2. Select [Connection type].
3. Select a setting, then press OK.
2. Select [Connection type].
3. Select a setting, then press OK.
[1 satellite (Single LNB)]: Select if you
have only one LNB.
have only one LNB.
[2 satellites (DiSEqC Mini)]: Select if
you have 2 LNBs.
you have 2 LNBs.
[3 or 4 satellites (DiSEqC 1.0)]: Select
for 3 or 4 LNBs.
for 3 or 4 LNBs.
[Unicable for 1 satellite]: Select if you
have a Unicable setup with 1 satellite.
have a Unicable setup with 1 satellite.
[Unicable for 2 satellites]: Select if you
have a Unicable setup with 2 satellite.
have a Unicable setup with 2 satellite.
Manual installation
If a transponder is skipped during installation,
you can test the signal strength of a
transponder or add a new transponder.
1. While you watch TV, press .
If a transponder is skipped during installation,
you can test the signal strength of a
transponder or add a new transponder.
1. While you watch TV, press .
2. Select [Setup] > [Search for satellite] >
[Manual installation], then press OK.
3. Select the LNB.
4. If you know the frequency of the
transponder (which can include several
[Manual installation], then press OK.
3. Select the LNB.
4. If you know the frequency of the
transponder (which can include several
channels), select [Frequency]and set the
frequency.
frequency.
5. Select [Search], then press OK.
6. If a new frequency is found, press
6. If a new frequency is found, press
[Store]to add the new transponder with its
channels.
channels.
Update satellite channels
1. While you watch TV, press .
1. While you watch TV, press .
2. Select [Setup] > [Search for satellite] >
[Update channels].
3. Follow the onscreen instructions to
complete the installation.
[Update channels].
3. Follow the onscreen instructions to
complete the installation.
4. Once complete, select [Finish], and then
press OK.
press OK.
Add and remove satellites
You can add or remove satellites at any
time, and install channels from new satellites.
Note: Before you add satellites, make sure
that the connection type is correct. See
time, and install channels from new satellites.
Note: Before you add satellites, make sure
that the connection type is correct. See
2. Select [Setup] > [Search for satellite],
then press OK.
3. Select [Add satellite], then press OK.
The TV searches for a satellite on the first
free LNB. This can take several minutes.
4. If no satellite is found, check the antenna
connections and the position of the dish
then press OK.
3. Select [Add satellite], then press OK.
The TV searches for a satellite on the first
free LNB. This can take several minutes.
4. If no satellite is found, check the antenna
connections and the position of the dish
antenna, then select [Search again].
5. If you are satisfied with the added satellite,
5. If you are satisfied with the added satellite,
select [Next] to install all channels from the
satellite.
The installation can take several minutes.
satellite.
The installation can take several minutes.