Akai MAX49 MAX 49 Manual De Usuario

 

 

 
Type:  The type of event that will be sent. The available settings are Aft (Aftertouch), MIDI CC, Inc/Dec1 
(Increment/Decrement, Mode 1), Inc/Dec2 (Increment/Decrement, Mode 2), Mackie, and HUI. 

MIDI Channel: This setting determines over which MIDI channel data is sent. The available settings are 
Common, USB A1-A16, and USB B1-B16. 

CC Number: If MIDI CC is the selected Type, this determines the MIDI CC. The available range is 000 – 
127. 

MIDI to DIN: Determines whether or not MIDI data is sent to the MIDI OUT (On) or not (Off). MIDI data will 
be sent to MAX49's USB connection regardless of this setting.  

Mode: This determines how the fader will act when touched: 

•  Absolute:  Touching the fader will cause it to jump immediately to that position. This mode is only 

available when the Type is set to Aftertouch or MIDI CC. 

•  Relative: Sliding your finger upward or downward along the fader will cause its setting to move upward 

or downward (regardless of your finger's absolute position on the fader).  

•  Relative2: This mode behaves like Relative Mode but with a finer resolution, allowing for more precise 

adjustment. This mode is only selectable in this menu when the Type is set to Aftertouch or MIDI CC. 
When a fader is in Relative Mode, you can manually put the faders in Relative2 Mode by holding 
[SHIFT] and sliding your finger along it. 

Min / Max: If Aftertouch is the selected Type, these determine the lowest (Min) and highest (Max) values. (If 
Min is higher than the Max, the fader's polarity will be reversed.) 

Msb / Lsb: If Inc/Dec1 is the selected Type, these determine the MSB (Most Significant Bit) and LSB (Least 
Significant Bit). The available range is 000 – 127. 

Value:  

•  If Inc/Dec1 is the selected Type, this determines the value sent by an Increment (CC#96) or Decrement 

(CC#97) message. The available range is 000 – 127.  

•  If Mackie or HUI is the selected Type, this determines what the fader will control using that protocol. 

The available settings are Fader 1-8, V-pot 1-8, and Master Level (Mackie only). 

 

 
Type:  The type of event that will be sent. The available settings are Note, CC#000-127, ProgramChange, 
ProgramBank, MackieControl, and HUI. 

MIDI Channel: This setting determines over which MIDI channel data is sent. The available settings are 
Common, USB A1-A16, and USB B1-B16. 

Note#: If Note is the selected Type, this assigns the note number. 

Velo: If Note is the selected Type, this assigns the velocity. The available range is 000-127. 

Mode: If Note, CC#000-127, Mackie, or HUI is the selected Type, this determines whether it is in Toggle or 
Momentary Mode. 

Invert: If CC#000-127 is the selected Type, the S-switches send 000 as the "off" value and 127 as the "on" 
value. This determines whether the values sent are normal (Off), as described above, or switched/inverted 
(On). 

Program Number / Pgm: If ProgramChange or ProgramBank is the selected Type, this determines the 
Program number. The available range is 000 – 127. 

Msb / Lsb: If ProgramChange or ProgramBank is the selected Type, these determine the MSB (Most 
Significant Bit) and LSB (Least Significant Bit). The available range is 000 – 127. 

MIDI to DIN: Determines whether or not MIDI data is sent to the MIDI OUT (On) or not (Off). MIDI data will 
be sent to MAX49's USB connection regardless of this setting.  

Value:  

•  If Inc/Dec1 is the selected Type, this determines the value sent by an Increment (CC#96) or Decrement 

(CC#97) message. The available range is 000 – 127.  

•  If Mackie or HUI is the selected Type, this determines what the S-switches will control using that 

protocol. The available settings are Fader 1-8, V-pot 1-8, and Master Level (Mackie only).