Maxview B2021 Prospecto
1
2
3
4
5
6
7
Locate the socket on the vehicle, free
of internal features such as cable,
seals, and any structural components
taking into account positions of doors,
windows, water, sewerage apertures.
You may wish the cable to enter the
vehicle under the seat, in a cupboard
or somewhere out of sight. Ensure
you have easy access from the
inside to feed the cable through.
Take care not to trap cable.
of internal features such as cable,
seals, and any structural components
taking into account positions of doors,
windows, water, sewerage apertures.
You may wish the cable to enter the
vehicle under the seat, in a cupboard
or somewhere out of sight. Ensure
you have easy access from the
inside to feed the cable through.
Take care not to trap cable.
Carefully offer up socket to vehicle,
correct alignment of holes is critical,
someone may need to be inside
the vehicle pulling through any
cable slack.
correct alignment of holes is critical,
someone may need to be inside
the vehicle pulling through any
cable slack.
Locate and fit self tapping screws.
Tighten clockwise, being careful not
to over tighten.
Tighten clockwise, being careful not
to over tighten.
Route cable(s) inside the vehicle to
your television and/or satellite
receiver. For the best interference
free reception do not run parallel to
electrical or other power cables.
Take care not to trap cable.
your television and/or satellite
receiver. For the best interference
free reception do not run parallel to
electrical or other power cables.
Take care not to trap cable.
Route cable(s) outside the vehicle
from terrestrial or satellite antenna
and connect (see above).
Close lid, * lid closes in intermediate
position when external cables are
connected.
from terrestrial or satellite antenna
and connect (see above).
Close lid, * lid closes in intermediate
position when external cables are
connected.
Lid must be fully closed when no
external cables are connected, and
during transit.
external cables are connected, and
during transit.
Re-assemble coaxial plug. Ensure
assembly is tight so plug does not
pull off cable.
assembly is tight so plug does not
pull off cable.
Strip away 7mm of inner insulation
around the inner copper wire. Check
that none of the screening braid is
touching the inner copper wire.
around the inner copper wire. Check
that none of the screening braid is
touching the inner copper wire.
Feed the inner copper wire through
connector and screw clockwise
to tighten.
connector and screw clockwise
to tighten.
Cut off inner copper wire to extend
3mm beyond plug body.
3mm beyond plug body.
Fitting ‘F’ connector models
B2007, B2008 and B2020
B2007, B2008 and B2020
Cut cable to required length. Strip
away 12mm of outer insulation.
Gather strands of screening braid,
twist together and wind back around
outer insulation. Cut tape to be flush
with outer insulation.
away 12mm of outer insulation.
Gather strands of screening braid,
twist together and wind back around
outer insulation. Cut tape to be flush
with outer insulation.
Slide opened claw over screening
braid and pinch to tighten. Slide
plastic connector over inner copper
wire and tighten screw securely (do
not overtighten).
braid and pinch to tighten. Slide
plastic connector over inner copper
wire and tighten screw securely (do
not overtighten).
Strip away 10mm of inner insulation
around the inner wire. Check none
of the screening braid is touching
the inner copper wire.
around the inner wire. Check none
of the screening braid is touching
the inner copper wire.
Fitting coaxial plug
models B2008 and B2021
models B2008 and B2021
Cut cable to required length. Unscrew
coaxial plug and slide cap over cable.
Strip away 12mm of outer insulation.
Gather strands of screening braid,
twist together and wind back around
outer insulation. Cut tape to be flush
with outer insulation.
coaxial plug and slide cap over cable.
Strip away 12mm of outer insulation.
Gather strands of screening braid,
twist together and wind back around
outer insulation. Cut tape to be flush
with outer insulation.
Fit coaxial plug and/or ‘F’ connector
appropriate to the model selected
– see below for plug fitting details.
appropriate to the model selected
– see below for plug fitting details.
From the outside offer the foam like
adhesive pad to desired position on
vehicle and use this as a template.
Using a bradawl or similiar tool, mark,
double check and then pierce 5 hole
positions. Check correct
hole positions before drilling.
adhesive pad to desired position on
vehicle and use this as a template.
Using a bradawl or similiar tool, mark,
double check and then pierce 5 hole
positions. Check correct
hole positions before drilling.
Drill holes with the specified drill
bits. Treat/seal any exposed materials
as required to prevent decay. Once
these are all drilled out, peel off one
side of the adhesive backing on the
foam like pad. Stick this to the vehicle
making sure all the holes are aligned
precisly.
bits. Treat/seal any exposed materials
as required to prevent decay. Once
these are all drilled out, peel off one
side of the adhesive backing on the
foam like pad. Stick this to the vehicle
making sure all the holes are aligned
precisly.
8mm drill bit = large holes
2.5mm drill bit = small holes
2.5mm drill bit = small holes
Feed stripped end of cable(s) into
the vehicle through 8mm holes
according to the model selected
(see above). Ensure correct cable
goes into correct hole and there is
not a crossover. Peel away the other
side of the foam like pad.
the vehicle through 8mm holes
according to the model selected
(see above). Ensure correct cable
goes into correct hole and there is
not a crossover. Peel away the other
side of the foam like pad.
NB. If you are fitting a single socket
(B2020 or B2021) one of the cable
feeding holes will be unused.
This can be used later should you
wish to upgrade your product to
a twin model–see upgrade kit details
on page 1 of these instructions.
(B2020 or B2021) one of the cable
feeding holes will be unused.
This can be used later should you
wish to upgrade your product to
a twin model–see upgrade kit details
on page 1 of these instructions.
8
1
3
2
4
1
2
3
4
Maxview reserve the right to change
specifications without prior notice.
specifications without prior notice.
9111201 Iss 3
MAXVIEW LIMITED
SETCHEY, KING’S LYNN
NORFOLK, PE33 OAT, ENGLAND
CUSTOMER HELPLINE
(01553) 811000
SETCHEY, KING’S LYNN
NORFOLK, PE33 OAT, ENGLAND
CUSTOMER HELPLINE
(01553) 811000
e-mail: cust_serv@maxview.ltd.uk
website: www.maxview.ltd.uk
website: www.maxview.ltd.uk
From
terrestrial
aerial
*
*
*
B2007
B2008
B2020
B2021
From
satellite
antenna
antenna
From
satellite
antenna
antenna
From
terrestrial
aerial
B2007, B2008
B2020
B2021
‘F’ connector to
satellite receiver
From ‘F’
connection
From ‘F’
connection
Hole
not used
Hole
not used
From
coaxial
connection
B2007, B2008
B2020
B2021
‘F’ connector to
satellite receiver
Coaxial plug
to TV
Coaxial plug
to TV
From
coaxial
connection