Gigaset A230 S30852-H2413-D201 Manual De Usuario
Los códigos de productos
S30852-H2413-D201
Lombok A130/AL130A/A230/AL230A / Großbritannien / A31008-M2412-L101-1-7619 / Lombok.fm / 12.02.2013
V
e
rsi
on 4
, 16.09
.2005
13
Specifications
Batteries
Technology: Nickel-metal-hydride (NiMH); Size: AAA (Micro, HR03); Voltage: 1.2 V;
Capacity: 450 - 1000 mAh
Capacity: 450 - 1000 mAh
General specifications
Questions and answers
If you have any queries about the use of your telephone, visit our website at
www.gigaset.com/service
www.gigaset.com/service
for 24-hour support. The table below contains a list of common problems and possible
solutions.
solutions.
DECT standard
is supported
GAP standard
is supported
Range
up to 300 m outdoors, up to 50 m indoors
Base station power supply
230 V ~/50 Hz
Environmental conditions
in operation
in operation
+5 °C to +45 °C, 20% to 75% relative humidity
Base station power consumption
A130/A230
AL130A/AL230A
In standby mode
– Handset in base station
– Handset in base station
– Handset outside base station
ca. 1.0 W
ca. 1.2 W
ca. 0.8 W
ca. 1.0 W
During a call
ca. 1.0 W
ca. 1.2 W
Problem
Cause
Solution
Nothing
appears in
the display.
appears in
the display.
The handset is not switched
on.
The batteries are flat.
on.
The batteries are flat.
Press the end call key
a
for approx.
5 seconds or place the handset in
the base station.
Charge or replace the batteries.
the base station.
Charge or replace the batteries.
No wireless
connection
to the base
station,
Base flashes in
the display.
connection
to the base
station,
Base flashes in
the display.
The handset is outside the
range of the base station.
The handset is not regis-
tered.
The base station is not
turned on.
range of the base station.
The handset is not regis-
tered.
The base station is not
turned on.
Move the handset closer to the base
station.
Register the handset
station.
Register the handset
Check the mains connector on the
base station
base station
Contact with liquid
If the device comes into contact with liquid:
1
1
Disconnect the power supply.
2
Remove the batteries and leave the battery compartment open.
3
Allow the liquid to drain from the device.
4
Pat all parts dry.
5
Place the device in a dry, warm place for at least 72 hours (not in a microwave,
oven etc.) with the battery compartment open and the keypad facing down (if ap-
plicable).
oven etc.) with the battery compartment open and the keypad facing down (if ap-
plicable).
6
Do not switch on the device again until it is completely dry.
When it has fully dried out, you will normaly be able to use it again.
Service (Customer Care)
www.gigaset.com/service
www.gigaset.com/service
Here you will find:
Here you will find:
◆
Frequently asked questions
◆
Free software and user manual downloads
◆
Compatibility checks
You cannot
hear a ringer/
dialling tone
from the fixed
line network.
hear a ringer/
dialling tone
from the fixed
line network.
The phone cord supplied
has not been used or has
been replaced by a new cord
with the wrong jack connec-
tions.
has not been used or has
been replaced by a new cord
with the wrong jack connec-
tions.
Please always use the phone cord
supplied or ensure that the
pin connections are correct when
purchasing from a retailer: 3-4
assignment of telephone leads/
EURO CTR37.
supplied or ensure that the
pin connections are correct when
purchasing from a retailer: 3-4
assignment of telephone leads/
EURO CTR37.
Error tone
sounds after
system PIN
prompt.
PIN forgotten.
sounds after
system PIN
prompt.
PIN forgotten.
The system PIN you have
entered is incorrect.
entered is incorrect.
Reset the system PIN to the default
0000
0000
All handsets are de-registered. All
settings are reset. All lists are
deleted.
settings are reset. All lists are
deleted.
Problem
Cause
Solution
!