Led Lenser LED Headlamp SEO 5 battery-powered 105 g Grey 6105 6105 Manual De Usuario

Los códigos de productos

6105

We are delighted that you have purchased one

of our products.

These are usage instructions to help you

familiarise yourself with your new purchase.

All the documents accompanying the product

must be read attentively before using the

product, preserved carefully and if the product

is transferred to a third party, the documents

must be handed over as well. This ensures that

maximum benefit is drawn from the product

and questions from users are anticipated

before they arise.

Above all, comply with the warnings and safety

instructions and dispose of the packaging

material properly.

Additional information for SEO with TEST IT

function

Your LED LENSER SEO 5 headlamp with the

item no. 6105 or 6106 (item no. 6005 and

6006: No TEST IT function ) is packaged with

a TEST IT function. This allows users to test

the brightness while the product is still in the

package. For testing, simply push the yellow

TEST IT button on the front of the package.

When testing, please do not look directly into

the light.

The TEST IT button is connected to the battery

housing of the SEO 5 via two wires and should

be removed prior to use.

To remove the TEST IT button and wires,

open the battery housing and remove the 3

x AAA batteries (see also “Changing of the

Alkaline batteries / Accumulator-Pack / NiMH-

Accumulators” further below). Separate the

two TEST IT button wires from the battery

housing by pulling on each wire until it releases

from the battery housing. Insert the 3 x AAA

batteries respectively accumulators noting

the correct polarity. Close the battery housing.

Please dispose and recycle the packaging and

TEST IT button with the wires according to the

local regulations.

Product

6005,

LED LENSER® SEO 5 grey

6105,

LED LENSER® SEO 5 grey (Blister)

6006,

LED LENSER® SEO 5 red

6106,

LED LENSER® SEO 5 red (Blister)

Version of the operating manual: 1.1

1. Battery set:

- 3 x Alkaline batteries AAA/LR03/Micro

(1.5 V DC) (scope of delivery) or

- 1 x Accumulator-Pack of SEO 7R

(not scope of delivery) or

- 3 x NiMH-Accumulator AAA/LR03/Micro

(1.2 V DC) (not scope of delivery)

2. Switching on and off

In the upper part of the headlamp housing of

the SEO 5, between battery box and the part

with the reflector lens, there is the switch

button. This switch button is used to turn the

SEO 5 on. It is also used to activate the various

Light Programs and Lighting Functions (see

section 5) and to switch between white light

and red light (see Point 5). In addition, you can

also activate the “Transport Lock” (see Point 6).

3. Focus

In the front, narrower region of the headlamp

housing is the reflector lens through which the

light of the white LED (see Point 5.1) is focused.

The reflector lens is held by a plastic ring. You

can rotate that plastic ring using two fingers,

and thus adjust the focus quickly and easily.

This so-called Speed Focus allows to adjust

the angle of the white light beam continuously.

Depending on whether you want to illuminate

an area in the distance or in front of you, you

also can adjust the angle of light beam to the

horizontal. For this you can simply tilt the part

of the head lamp, which contains the reflector

lens and the white LED. The screening allows

using also intermediate positions.

4. Smart Light Technology (SLT)

The SEO 5 is equipped with our Smart Light

Technology (SLT). Thanks to the use of a

microcontroller, the light output of the LED

can be controlled and the user can use various

Light Programs and Light Functions. By using

a single switch it was possible to design the

interface to be simple and user-friendly. The

SEO 5 can give the user light in different ways.

There are thus two Light Programs and a

number of Light Functions available. To switch

the pocket torch on and off and to select the

various Light Functions etc., the switch (see

Point 2) has to be used.

What basically applies is that the brightness

of the SEO 5 is monitored by the in-built

temperature control unit.

5. Light Programs and Light Functions

In the SEO 5 are two LEDs (LED =

Light Emitting

Diode) installed.

The white LED is very strong, ideal for normal

use, for example if the Speed Focus or the

adjustment of the angle of light beam to the

horizontal should be used. This very bright

white light might be not good when your eyes

have become accustomed through the so-

called dark adaptation to low ambient light.

Otherwise than with the use of the white light,

it remains the current adjustment of the eye

to low brightness obtained when the red light

of the second LED is used. The focus and the

angle of the light to the horizontal of the red

LED, which is located laterally next to the

reflector-lens, can not be adjusted.

In order to switch between the white and the

red LED, when the SEO 5 is off, press and hold

the switch button for 2 seconds. The head lamp

will change from red to white or from white to

red, and then release the switch button before

the lights go out, because if you press too long

the switch button you activate the „Transport

Lock“ (see section 6)!

The points below deal with the Light Functions

of the white LED (Light Program White / Point

5.1) and the red LED (Light Program „Red Night

Vision“ / Point 5.2).

5.1 Light Program White

If the Light Program White is enabled (see

Point 5), you can use the white, focusable light

of the headlamp.

When the switch button is pushed, while the

SEO 5 is off, the headlamp glows in the Light

Function Power at full brightness. When you

English

Page 02-05