Manualsbrain.com
  1. Manuales
  2. Marcas
  3. TP-LINK
  4. AC750
  5. Prospecto

TP-LINK AC750 RE200 Prospecto

Los códigos de productos
RE200
Descargar
Página de 2
Immediately push the
       button on your 
Range Extender.
1
2
2
1
Plug your Range Extender into a power outlet 
near
 your Router/AP.
LED Explanation
Quick Setup using the WPS Button
RE200
Applicable Model: 
Method TWO: 
Setup using your Web Browser
WPS
Method ONE: 
Quick Setup using the WPS Button
Push the WPS button 
on your Router/AP.
If the WPS connection fails, please go to Method TWO.
       Wait until the 
‘       ’ and ‘       ’  
LEDs light up.
Method ONE
Quick 
Installation 
Guide
Use this if your Router or Access Point(AP) supports WPS
Frequently Asked Questions (FAQ)
A1:
 While the Range Extender is plugged into a power outlet, 
press the RESET button with a pen for 1 second. Wait 2 
seconds until all the LEDs flash once.
OR
A2:
 Use your web browser to log into the management page, 
go to “System Tools -> Factory Defaults” and click 
“Restore”
. Wait 5 seconds until all the LEDs flash once.
Q1. How to reset the Range Extender?
A: First, make sure your computer is connected to the extender network and disconnected from any other network. Second, make 
sure your computer is set to “
Obtain an IP address automatically
”.
RESET
The Range Extender shares the same Wi-Fi Network Name (SSID) and 
Wi-Fi Password
 with your main Router/AP. 
Password (ABCDEF)
SSID (TP-LINK_XXGHz_XXX)
Password (ABCDEF)
SSID (TP-LINK_XXGHz_XXX)
Q2. I typed http://tplinkextender.net in the browser URL bar, why can't I see the quick setup page?     
A:
 Please visit “www.tp-link.com
”
, find “Support>Contact Technical Support>Hotline Support” for more information. 
Q3. What’s the technical support hotline?
RESET
ETHERNET
Power on
Push the two WPS buttons
Enjoy!
7106504739    RE
V1.0.0 
3
Keep the Range Extender away from
 devices like 
cordless phones, Bluetooth devices and Microwave Ovens 
to minimize wireless interference.
If possible, try to place your extender in open corridors or 
spacious locations
 rather than a crowded room.
far away
After you have configured your Range Extender, move it to a location for the best signal quality and coverage in your house. The Range Extender will 
automatically reconnect to your main Router/AP within about 30 seconds after you plug it into another power outlet.   * Keep the following in mind:
Relocate
       The ‘        ’ LED should go 
from flashing to solid, showing 
that WPS connection has 
succeeded, then it will turn off 
in 2 minutes.
The ideal location for your Range Extender is Halfway 
between your main Router/AP and Wi-Fi-enabled devices.  
If possible, try to place your Range Extender in a location 
where the 2.4G/5G LEDs are Green.
5G/2.4G
Solid Green:
 The Range Extender is connected 
to the 5G/2.4G wireless network of your main 
Router/AP, and the signal strength is strong.
Solid Red:
 The Range Extender is connected 
to the 5G/2.4G wireless network of your main 
Router/AP, but the signal strength is weak.
Off:
 The Range Extender isn’t connected to 
your main Router/AP. 
On:
 The Range Extender’s wireless function is 
enabled.
Off:
 The Range Extender’s wireless function is 
disabled.
(Wireless Signal)
(ETHERNET)
On:
 A device is connected to the ETHERNET 
port, but there is no activity.
Flashing
: A device is connected to the 
ETHERNET port, and is active.
Off:
 No device is connected to the ETHERNET 
port.
(Power)
On:
 The Range Extender is on.
Off:
 The Range Extender is off.
On:
 The Range Extender has established a 
secure connection. 
Flashing:
 The Range Extender is establishing a 
secure connection.
Off:
 No active connection.
(RE)