Velcro tape sew-on Hook pad (L x W) 25 m x 100 mm Black Velcro 25 m E00110033011425 Hoja De Datos
Los códigos de productos
E00110033011425
INSTRUCCIONES DE TRABAJO
Versión nº: 2 Fecha de revisión: Septiembre 2011
IDT-605: Fichas técnicas de producto
Velcro Europe, S.A.: Toda la documentación gestionada mediante el software “GESDOC” está sometida a un sistema de control de la documentación. Cualquier copia impresa debe ser considerada
instantáneamente obsoleta a excepción de la “copia controlada”. El contenido de este documento debe considerarse confidencial y de uso interno
instantáneamente obsoleta a excepción de la “copia controlada”. El contenido de este documento debe considerarse confidencial y de uso interno
PRESSURE SENSITIVE PS-14
Base material :
Rubber resin
Colour :
Amber
Shelf Life :
Maximum 3 Years, when stored in dark area, at temperature of 10°C to 30°C.
Suggested uses :
On most clean and smooth surfaces. (Except any kind of plastifying)
Adhesives Properties
Peel Stren
gth 180° :
Curing time 20 minutes
Minimum 8 N/cm
Test method : FINAT ; FTM 1
Average 15 N/cm
Curing time 24 hours
Minimum 10 N/cm
Test method : FINAT ; FTM 1
Average 17 N/cm
Static Shear Strength:
7 days
Test method : FINAT ; FTM 8
Softening Point:
90°C
Test method : ASTM D-816
FINAT: Fédération Internationale des fabricants transformateurs d'Adhésifs et Thermocollants. ASTM: American Society for Testing and Materials.
Tested on: Anodized aluminium plates under laboratory conditions. (23°C ± 2 and 60 ± 10 % R.H.)
Tested on: Anodized aluminium plates under laboratory conditions. (23°C ± 2 and 60 ± 10 % R.H.)
Resistance properties
Oxidation
Poor
Plastifying, oils
Poor
High relative humidity
Poor
Polar solvents (M.E.K. etc.)
Poor
Non-polar solvents (gasoline, etc.)
Suitable
Migration
Poor
High temperature
Suitable
Low temperature
Suitable
U.V. radiation
Poor
Temperature Range:
-15°C to +90°C (Depending on loading and Relative Humidity).
General Directions for Use
Application temperature range: 20°C to 30°C.
Degrease the substrate with e.g. alcohol or spirit. (The substrate must be free of grease, moisture, dust, silicones, etc.).
Remove the protective paper and press the tape firmly into contact with the substrate, with special attention to the edges.
Preferably, allow substrate and pressure sensitive tape to stand for 24 hours after applying load.
Degrease the substrate with e.g. alcohol or spirit. (The substrate must be free of grease, moisture, dust, silicones, etc.).
Remove the protective paper and press the tape firmly into contact with the substrate, with special attention to the edges.
Preferably, allow substrate and pressure sensitive tape to stand for 24 hours after applying load.
* Internal norm of VESA
The information included in this Technical Sheet is based on reliable test and trials. Average value as a reference only, not a nominal specification. Given the diversity of uses of our
products we advice our customers to assure themselves that the product meets the requirements of their application. The responsibility for the application and use of the product
remains with the customer.
The information included in this Technical Sheet is based on reliable test and trials. Average value as a reference only, not a nominal specification. Given the diversity of uses of our
products we advice our customers to assure themselves that the product meets the requirements of their application. The responsibility for the application and use of the product
remains with the customer.
Elaborado:
J.C. Lima
Revisado:
E. Ducet
Autorizado:
J. Jacobs
Fecha: 11.10.11
ANEXO: IDT – 605-B
FTP 500 Versión 5